MSA  Vol.2 No.11 , November 2011
Influence of Degree of Cold-Drawing on the Mechanical Properties of Low Carbon Steel
ABSTRACT
Low carbon steel metal is used for the manufacture of nails. Steel wire with <0.3% C content is cold-drawn through a series of drawing dies to reduce the diameter of the wire to the required diameter of the nails. A 0.12%w C steel wire cold drawn progressively by 20%, 25%, 40% and 50% was investigated. The influence of the degree of cold drawing on the mechanical properties of the carbon steel material were studied using the tensile test, impact test and hardness test experiments in order to replicate the service condition of the nails. The tensile test was done on a Montanso® tensometer to investigate the yield strength and the tensile strength of the material as the degree of deformation increases. An Izod test was used to determine the impact toughness of the steel using the Hounsfield impact machine and the hardness numbers were obtained for the different degrees of drawn deformation of the steel on the Brinnel tester. The study used the stress-strain relationship of the tensile test experiment to study the effect of the degree of cold-drawing deformation on the yield strength and tensile strength properties of the low carbon steel. The yield strength of the material was observed to reduce with increasing degree of cold-drawing, an indication of reduction in the ductility and the tensile strength of the material reduced with increasing degree of cold-drawn deformation. The ability of the material to resist impact loads when nails are hammered reduced with increasing degree of drawn deformation as a result of strain hardening of the material after the drawing operation. However the resilience of the material to further cold drawn deformation increased with increasing degree of deformation as evident in the Brinnel hardness number which increases with the degree of drawing deformation. This is an indication of the material’s approach to brittleness as the degree of drawn deformation increases.

Cite this paper
nullN. Raji and O. Oluwole, "Influence of Degree of Cold-Drawing on the Mechanical Properties of Low Carbon Steel," Materials Sciences and Applications, Vol. 2 No. 11, 2011, pp. 1556-1563. doi: 10.4236/msa.2011.211208.
References
[1]   F. J. Humphreys and M. Hatherly, “Recrystallization and Related Annealing Phenomena,” 2nd Edition Elsevier Ltd. U. K., 2004.

[2]   K. Sawamiphakdi, G. D. Lahoti, J. S. Gunasekara and R. Kartik, “Development of Utility Programs for a Cold Drawing Process,” Journal of Materials Processing and Technology, Vol. 80-81, 1998, pp. 392-397. doi:10.1016/S0924-0136(98)00118-6

[3]   M. Zidani, M. Messaondi, C. Derfont, T. Bandin, P. Solas and M. H. Mathon, “Microtructure and Textures Evolution during Annealing of a Steel Drawn Wires,” Roznov pod Radhostem, Czech Republic EU.5, 2010, pp. 18-21

[4]   T. Fuller, R. M Brannon, “On the Thermodynamic Requirement of Elastic Stiffness Anisotropy in Isotropic Materials,” International Journal of Engineering Science, Vol. 49, 2011, pp. 311-321. doi:10.1016/j.ijengsci.2010.12.017

[5]   S. Zaefferer, J. C. Kuo, Z. Zhao, M. Winning and D. Raabe, “On the Influence of the Grain Boundary Misorientation on the Plastic Deformation of Aluminum Bi- crystals,” Acta Materialia, Vol. 51, 2003, pp. 4719- 4735. doi:10.1016/S1359-6454(03)00259-3

[6]   S. Ganapathysubramanian and N. Zabaras, “Deformation Process Design for Control of Microstructure in the Presence of Dynamic Recrystallization and Grain Growth Mechanism,” International Journal of solid and structures, Vol. 41, 2004, pp. 2011-2037.

[7]   G. V. S. S. Prasad, M. Goerdeler and G. Gottstein, “Work Hardening Model Based on Multiple Dislocation Densities,” Material Science and Engineering A, Vol. 400-401, 2005, pp. 231-233. doi:10.1016/j.msea.2005.03.061

[8]   M. Domoinkova, M. Peter and M. Roman, “The Effect of Cold Work on the Sensitization of Austenitic Stainless Steels,” MTAEC 9, Vol. 41, No. 3, 2007, pp. 131-134.

[9]   Z. Huda, “Effect of Cold Working and Recrystallization on the Mecristructure and Hardness of Commercial-Purity Aluminum,” European Journal of Scientific Research, Vol. 26, No. 4, 2009, pp. 549-557.

[10]   S. J. Pawlak and H. J. Krzton, “Cold Worked High Alloy Ultra-High Strength Steels with Aged Matensite Structure,” Journal of Achievement in Materials and Engineering, Vol. 36, No. 1, 2009, pp. 18-24.

[11]   J. Schindler, M. Jano?ec, E. Místecky, M. R??i?ka, L. A. ?í?ek Dobrzdviski, S. Rusz and P. Svenanek, “Effect of Cold Rolling and Annealing on Mechanical Properties of HSLA Steel,” Achives of Materials Science and Engineering, Vol. 36, No. 1, 2009, pp. 41-47.

[12]   J. Schindler, M. Janosec, E. Mistecky, M. and L. , “Influence of Cold Rolling and Annealing on Mechanical Properties of Steel QStE 420,” Journal of Achievement in Materials and Manufacturing Engineering, Vol. 18, No. 1-2, 2006, pp. 231-234.

[13]   J. A. Wert, Q. Liu and N. Hansen, “Dislocation Boundary Formation in Cold-Rolled Cube-Orientation Al Single Crystal,” Acta Materialia, Vol. 45 No. 6, 1997, pp. 2565-2576. doi:10.1016/S1359-6454(96)00348-5

[14]   A. Godfrey, D. J. Jensen and N. Hansen, “Slip Pattern Microstructure and Local Crystallography in an Aluminium Single Crystal of Brass Orientation {110}<112>,” Acta Materialia, Vol. 46, No. 3, 1998, pp. 823-833. doi:10.1016/S1359-6454(97)00315-7

[15]   A. Godfrey, D. J. Jensen and N. Hansen, “Recrystallization of Channel Die Deformed Single Crystals of Typical Rolling Orientation,” Acta Materialia, Vol. 49, 2001, .pp. 2429-2440. doi:10.1016/S1359-6454(01)00148-3

[16]   C. Maurice, J. H. Driver, “Hot Rolling Texture of F.C.C. Metals-Part 1. Experimental Results on Al Sample and Polycrystals,” Acta Materialia, Vol. 45, No. 11, 1997, pp. 4627-4638. doi:10.1016/S1359-6454(97)00115-8

[17]   F. Bossom and J. H. Driver, “Deformation Banding Mechanisms during Plain Strain Compression of Cube Oriented F.C.C. Crystals,” Acta Materialia, Vol. 48, 2000, pp. 2101-2115. doi:10.1016/S1359-6454(00)00042-2

[18]   N. Hansen and X. Huang, “Microstructure and Flow Stress of Polycrystals and Single Crystals,” Acta Materialia, Vol. 46, No. 5, 1998, pp. 1827-1836. doi:10.1016/S1359-6454(97)00365-0

[19]   A. Akpari, G. H. Hasani and M. J. Jam, “An Experimental Investigation of the Effect of Annealing Treatment on Strain Inhomogeneity in the Cross-Section of Drawn Copper Wires,” Metal, Roznov pod Radhostem, Czech republic, EU. 18-20 May 2010.

[20]   F. Yan, C. Ma, J. Q. Jiang, H. P. Feng and S. T. Zha, “Effect of Cumulative Strain on Texture Characteristics during Wire Drawing of Eutectoid Steels,” Scripta Materialia, Vol. 59, 2008, pp. 850-853. doi:10.1016/j.scriptamat.2008.06.048

[21]   E. N. Popova, V. V. Popov, E. P. Romanov, N. E. Hlebova and A. K. Shikov, “Effect of Deformation and Annealing on Texture Parametal of Composite Cu-Nb Wire,” Scupta Materialia, Vol. 51, 2004, pp. 727-731. doi:10.1016/j.scriptamat.2004.05.037

[22]   M. Ferry, “Influence of Fine Particle of Grain Coarsening within an Orientation Gradient,” Acta Materialia, Vol. 53, 2005, pp. 773-783. doi:10.1016/j.actamat.2004.10.030

[23]   Z. Michael, “Microstructure Evolution in Pearlitic Steels during Wire Drawing,” Acta. Materialia, Vol. 50, 2002, pp. 4431-4447. doi:10.1016/S1359-6454(02)00281-1

[24]   A. Skolyszewski, J. Luksza and M. Packo, “Some Problems of Multi-Stage Fine Wire Drawing of High-Alloy Steels and Special Alloys,” Journal of Material Processing Technology, Vol. 60, 1996, pp. 155-160. doi:10.1016/0924-0136(96)02321-7

[25]   A. Skolyszewski and M. Packo, “Back Tension Value in the Fine Wire Drawing Process,” Journal of Material Processing Technology, Vol. 80-81, 1998, pp. 380-387. doi:10.1016/S0924-0136(98)00116-2

[26]   A. L. R. de Castro, H. B. Campos and P. R. Cetlin, “Influence of Die Semi-Angle on Mechanical Properties of Single and Multiple Pass Drawn Copper,” Journal of Materials Process and Technology, Vol. 60, 1996, pp. 179-182. doi:10.1016/0924-0136(96)02325-4

[27]   D. G. Cram, H. S. Zurob, Y. J. M. Brechet and C. R. Hutchinsm, “Modeling Discontinuous Dynamic Recrystallization Using a Physically Based Model for Nucleation,” Acta. Materialia, Vol. 57, 2009, pp. 5218-5228. doi:10.1016/j.actamat.2009.07.024

[28]   P. Les, H. P. Stuewe and M. Zehetbauer, “Hardening and Strain Rate Sensitivity in Stage IV of Deformation in F.C.C. and B.C.C. Metals,” Materials Science and Engineering, Vol. A234-236, 1997, pp. 453-455.

[29]   Y. Estrin, L. S. Tóth, A. Molinari and Y. Bréchet, “A Dislocation-Based Model for All Hardening Stages in Large Strain Deformation,” Acta Materialia, Vol. 46, No. 15, 1998, pp. 5509-5522. doi:10.1016/S1359-6454(98)00196-7

[30]   O. Bouaziz, S. Allain and C. Scott, “Effect of Grain and Twin Boundaries on the Hardering Mechanisms of Twinning-Induced Plasticity Steels,” Scripta Materialia, Vol. 58, 2008, pp. 484-487. doi:10.1016/j.scriptamat.2007.10.050

[31]   R. E. Smallman and R. J. Bishop, “Modern Physical Metallurgy and Materials Engineering Science, Process, Applications,” Butterworth-Heinemann 1999, 6th Edition, London.

[32]   S. Panwar, D. B. Goel and O. P. Pandey, “Effect Interfacial of Cold Work and Aging on Mechanical Properties of Surface Energy Copper Bearing HSLA-100 Steel,” Bulletin Material Science, Vol. 28, No. 3, 2005, pp. 259-265. doi:10.1007/BF02711258

[33]   J. Luksza, J. Majta, M. Burdek, M. Ruminski, “Modeling and Measurement of Mechanical Behavior in Multi-Pass Drawing Process,” Journal of Materials and Processing Technology, Vol. 80-81, 1998, pp. 398-405. doi:10.1016/S0924-0136(98)00119-8

[34]   F. Knap, “Drawing of Square Twisted Wire,” Journal of Material Processing Technology, Vol. 60, 1996, pp. 167-170. doi:10.1016/0924-0136(96)02323-0

[35]   O. O. Isimijola, “Assessment of Locally Produced Nails,” M.Sc Project work of University of Ibadan, Ibadan, 2010.

[36]   K. L. Murty, 2011 ‘Tension Test’ http://www4.ncsu.edu/~murty/MAT450/NOTES/tandhtests.pdf (considere construction and other factors-resilience, etc)

[37]   EPI Inc. 2011 “Metal Fatigue-Why Metal Parts Fail From Repeatedly-Applied Loads,” http://webcache.googleusercontent.com/search?q=cache:mqdpB8n3EJoJ:www.epieng.com/mechanical_engineering_basics/fatigue_in_metals.htm+fatigue+uts+ratio&cd=10&hl=en&ct=clnk&gl=ng&source=www.google.com.ng

[38]   Matweb 2011 “Unit of measure converter,” http://www.matweb.com/tools/unitconverter.aspx

 
 
Top