OALibJ  Vol.2 No.12 , December 2015
Study of Influence of the Peak Current Time in Microstructure of a Coating Hard Made by GTAW-P Process
Abstract: This paper presented analysis in order to show the influence of welding pulse parameters on the microstructure of the deposit, where a coating performed by GTAW-P process (Tungsten Arc Welding with the Atmosphere Gas with deposition Powder). The coating was an alloy of cobalt based on a substrate of a steel SAE 1020. The coating was performed with pulsed current between 120 and 180 A, and the variations of pulse parameters occurred between the time base and peak currents. Metallographic analysis by electronic scanning microscopy (SEM), micro hardness testing and determination of the dilution rate of the material were carried out. Thus, the results demonstrated that sample 3 showed better results, such as the size of finer grains, medium high hardness about 65 HRC, 4.3% dilution rate and a lower heat transfer. Therefore, the spectrum shown by scanning electron microscopy revealed the presence of hard carbides (Co, Cr and W) in interdendritic region of the deposit, which explained the high levels of hardness.
Cite this paper: Moreira, E. , Moselli, P. and Moreno, J. (2015) Study of Influence of the Peak Current Time in Microstructure of a Coating Hard Made by GTAW-P Process. Open Access Library Journal, 2, 1-6. doi: 10.4236/oalib.1102233.

[1]   Gomes, J.H.F. (2010) Análise e otimização da soldagem de revestimento de chapas de aço ABNT 1020 utilização de arame tubular inoxidável austenítico. Master Thesis, Universidade Federal de Itajubá, Itajubá.

[2]   Moselli, P.C., De Oliveira, M.F. and Moreno, J.R.S. (2013) Deposited Properties in Hardfacing SAE 1020 Substrate by Using Alloy Welding GTAW Stellite 6 in Powder Form. 22nd International Conference on Production Research, Fóz do Iguaçu.

[3]   Ibrahim, I.A., Mohamat, S.A., Amir, A. and Ghalib, A. (2012) The Effect of Gas Metal Arc Welding (GMAW) Processes on Different Welding Parameters. Procedia Engineering, 41, 1502-1506.

[4]   Lakshminarayanan, A.K., Balasubramanian, V., Varahamoorthy, R. and Babu, S. (2008) Predicting the Dilution of Plasma Transferred Arc Hardfacing of Stellite on Carbon Steel Using Response Surface Methodology. Metals and Materials International, 14, 779-789.

[5]   Buchely, M.F., Gutierrez, J.C., León, L.M.E. and Toro, A. (2005) The Effect of Microstructure on Abrasive Wear of Hardfacing Alloys. Tribology International, 259, 52-61.

[6]   Karadeniz, E., Ozsarac, U. and Yildiz, C. (2007) The Effect of Process Parameters on Penetration in Gas Metal Arc Welding Processes. Material and Design, 28, 649-656.

[7]   Nunes, E.B., Cavalcante, N.E., Barreto, A.S., Silva, A.I.N. and Motta, M.F. (2015) Evaluation of the Effect of the Heat Input in the Super Stainless Steel Deposition by Powder Plasma Process. Soldagem & Inspeção, 20.

[8]   Liyanage, T., Fisher, G. and Gerlich, A.P. (2010) Influence of Alloy Chemistry on Microstructure and Properties in NiCrBSi Overlay Coatings Deposited by Plasma Transferred Arc Welding (PTAW). Surface and Coatings Technology, 205, 759-765.

[9]   Prasad, K.S., Rao, C.S. and Rao, D.N. (2011) A Study on Weld Quality Characteristics of Pulsed Current Micro Plasma Arc Welding of SS304L Sheets. International Transaction Journal of Engineering, Management, & Applied Sciences & Technologies, 2, 437-446.