JFCMV  Vol.3 No.2 , April 2015
Erosion of Grooved Surfaces by Cavitating Jet with Hydraulic Oil
ABSTRACT
To study the effect of impingement surface geometry, a cavitation erosion experiment was conducted using a submerged cavitating jet rig with hydraulic oil. The test setup comprised a test chamber with a long-orifice nozzle, a hydraulic pump with an electric motor, hydraulic auxiliaries, including valves, a cooler, a filter, a reservoir, and measuring instruments, including pressure gages and a thermometer. Hexahedral specimens made of aluminum alloy with flat and grooved surfaces and oblique angles were prepared. Hydraulic oil with a viscosity grade of 32 was used at 40°C as the test fluid. The upstream absolute pressure was kept at 10.1 MPa and the cavitation numbers were set at 0.02 - 0.04. The results of this experiment yielded the following conclusions. The mass loss of the grooved specimens did not increase monotonically as the exposure time increased. The standoff distances at the maximum mass loss for the flat and grooved specimens were almost equivalent. The mass loss decreased as the oblique angle increased and the cavitation number increased, regardless of the presence of grooves. The surfaces were eroded in a ring-like region, but the region elongated as the angle increased. For the grooved specimens, the ridges on the ring were eroded, and when the directions of the grooves and the flow matched, the roots and flanks were severely eroded.

Cite this paper
Kazama, T. , Kumagai, K. , Osafune, Y. , Narita, Y. and Ryu, S. (2015) Erosion of Grooved Surfaces by Cavitating Jet with Hydraulic Oil. Journal of Flow Control, Measurement & Visualization, 3, 41-50. doi: 10.4236/jfcmv.2015.32005.
References
[1]   Plesset, M.S. and Devine, R.E. (1966) Effect of Exposure Time on Cavitation Damage. Journal of Basic Engineering, Transactions of ASME, 88, 691-705. http://dx.doi.org/10.1115/1.3645943

[2]   Knapp, R.T., Daily, J.W. and Hammitt, F.G. (1970) Cavitation. McGraw Hill, New York.

[3]   Caupin, F. and Herbert, E. (2006) Cavitation in Water: A Review. Comptes Rendus Physique, 7, 1000-1017. http://dx.doi.org/10.1016/j.crhy.2006.10.015

[4]   Peng, G. and Shimizu, S. (2013) Progress in Numerical Simulation of Cavitating Water Jets. Journal of Hydrodynamics, B, 25, 502-509. http://dx.doi.org/10.1016/S1001-6058(11)60389-3

[5]   Van Terwisga, T.J.C., Fitzsimmons, P.A., Li, Z. and Foeth, E.J. (2009) Cavitation Erosion—A Review of Physical Mechanisms and Erosion Risk Models. Proceedings of the 7th International Symposium on Cavitation CAV2009, Ann Arbor, 17-22 August 2009, 14.

[6]   ASTM (1989) Standard Method of Vibratory Cavitation Erosion Test. Annual Book ASTM Standards, G32.85, 142- 147.

[7]   ASTM (1995) Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet. Annual Book of ASTM Standards, G134.95, 529-540.

[8]   Lichtarowicz, A. (1972) Use of a Simple Cavitating Nozzle for Cavitation Erosion Testing and Cutting. Nature; Physical Science, 239, 63-64. http://dx.doi.org/10.1038/physci239063a0

[9]   Kleinbreuer, W. (1977) Kavitationserosion in Hydraulischen Systemen. Industrie-Anzeiger, 99, 609-613.

[10]   Yamaguchi, A. and Shimizu, S. (1987) Erosion Due to Impingement of Cavitating Jet. Journal of Fluids Engineering, Transactions of ASME, 109, 442-447. http://dx.doi.org/10.1115/1.3242686

[11]   Momma, T. and Lichtarowicz, A. (1995) Study of Pressures and Erosion Produced by Collapsing Cavitation. Wear, 186-187, 425-436. http://dx.doi.org/10.1016/0043-1648(95)07144-X

[12]   Soyama, H., Lichtarowicz, A., Momma, T. and Williams, E.J. (1998) A New Calibration Method for Dynamically Loaded Transducers and Its Application to Cavitation Impact Measurement. Journal of Fluids Engineering, Transactions of ASME, 120, 712-718.

[13]   Soyama, H. (2013) Effect of Nozzle Geometry on a Standard Cavitation Erosion Test Using a Cavitating Jet. Wear, 297, 895-902. http://dx.doi.org/10.1016/j.wear.2012.11.008

[14]   Steller, J. (1999) International Cavitation Erosion Test and Quantitative Assessment of Material Resistance to Cavitation. Wear, 233-235, 51-64. http://dx.doi.org/10.1016/S0043-1648(99)00195-7

[15]   Mann, B.S. and Arya, V. (2002) An Experimental Study to Correlate Water-Jet Impingement Erosion Resistance and Properties of Metallic Materials and Coatings. Wear, 253, 650-661.
http://dx.doi.org/10.1016/S0043-1648(02)00118-7

[16]   Hattori, S., Goto, Y. and Fukuyama, T. (2006) Influence of Temperature on Erosion by a Cavitating Liquid Jet. Wear, 260, 1217-1223. http://dx.doi.org/10.1016/j.wear.2005.08.001

[17]   Hattori, S., Hirose, T. and Sugiyama, K. (2010) Prediction Method for Cavitation Erosion Based on Measurement of Bubble Collapse Impact Loads. Wear, 269, 507-514.
http://dx.doi.org/10.1016/j.wear.2010.05.015

[18]   Kazama, T. and Shimizu, K. (2007) Erosion Due to Impingement of Submerged Cavitating Jets in Tap Water, Biodegradable and Mineral Oils. Proceedings of the Tenth Scandinavian International Conference on Fluid Power, SICFP’07, Tampere, 21-23 May 2007, 91-105.

[19]   Kazama, T. and Miura, Y. (2007) Reduction in Submerged Jet Cavitation Erosion (Flow Control by Geometry Close to Nozzle Outlets and Impinged Surfaces). Transactions of Japan Fluid Power System Society, 38, 77-82. http://dx.doi.org/10.5739/jfps.38.77

[20]   Shimizu, S., Yamaguchi, A. and Kazama, T. (1991) Erosion Due to Impingement of a Cavitating Jet (2nd Report: Effects of Nozzle Holder and Configuration of Impingement Surface). Journal of Japan Hydraulics and Pneumatics Society, 22, 57-62. http://dx.doi.org/10.5739/jfps1970.22.57

[21]   Yamaguchi, A., Wang, X. and Kazama, T. (1997) Erosion Due to Impingement of a Cavitating Jet (4th Report: Effects of Nozzles Shape and Upstream Pressure Pulsation). Journal of Japan Hydraulics and Pneumatics Society, 28, 353- 358. http://dx.doi.org/10.5739/jfps1970.28.353

[22]   Kazama, T. and Yamaguchi, A. (2000) Effects of Configuration of Nozzles, Outlets of Nozzles and Specimens on Erosion Due to Impingement of Cavitating Jet. Proceedings of the 48th National Conference on Fluid Power, Chicago, 4-6 April 2000, 263-272.

[23]   Yamaguchi, A., Kazama, T., Inoue, K. and Onoue, J. (2001) Comparison of Cavitation Erosion Test Results between Vibratory and Cavitating Jet Methods. International Journal of Fluid Power, 2, 25-30.
http://dx.doi.org/10.1080/14399776.2001.10781099

[24]   Kazama, T., Kumagai, K., Osafune, Y., Narita, Y. and Ryu, S. (2013) Effects of Oblique Surfaces with Grooves on Erosion by Cavitating Oil Jet. Proceedings of the 12th International Symposium on Fluid Control, Measurement and Visualization (FLUCOME 2013), Nara, 18-22 November 2013, OS1-03-4, 1-10.

[25]   Sugimoto, Y., Jibiki, Y. and Sato, K. (2010) Behavior and Erosion of Cavitating Jet Impinging on Oblique Surface. Japanese Journal of Multiphase Flow, 24, 697-702. http://dx.doi.org/10.3811/jjmf.24.697

[26]   Kazama, T., Kumagai, K., Miura, Y. and Narita, Y. (2009) Reduction and Enlargement of Erosion by a Submerged Cavitating Jet with Geometric Control. Proceedings of the 9th Pacific Rim International Conference on Water Jetting Technology, Koriyama, 20-23 November 2009, 123-131.

 
 
Top