MSA  Vol.6 No.1 , January 2015
Heat Resistant Properties of Some Elements-Incorporated Diamond-Like Carbon Films and Their Trial Applications for Micro End Mill Coatings
ABSTRACT
In this article, the results obtained from a study carried out on the some elements-incorporated diamond-like carbon (DLC) films are reported. All the films were deposited using plasma-based ion implantation (PBII) technique. The deposited films were annealed at 400, 650 and 900 in an air atmosphere for 1 hour. The effects of adding hydrogen, silicon/oxygen and silicon/nitrogen into the DLC film on chemical composition, friction coefficient and corrosion resistance were investigated. The films coated micro end mills performance was also assessed. The results indicate that all the films showed almost constant atomic contents of C, Si, O and N until annealing at 400. However, the films were completely destroyed at 650 with the increased Si and O contents, while the C content decreased. The incorporation of silicon/oxygen and silicon/nitrogen into the DLC exhibited lower values of friction coefficients than the hydrogenated DLC (DLC and H-DLC) before and after annealing at 400, whereas all the films presented the same values of friction coefficients after annealing at 650 due to the completely destroy of the films. Furthermore, the incorporation of silicon/nitrogen into the DLC also exhibited better corrosion resistance and unbroken micro end mills performance on their surfaces. Thus, the incorporation of silicon/nitrogen into the DLC film can be considered beneficial in improving the micro end mills performance.

Cite this paper
Jongwannasiri, C. , Moolsradoo, N. and Watanabe, S. (2015) Heat Resistant Properties of Some Elements-Incorporated Diamond-Like Carbon Films and Their Trial Applications for Micro End Mill Coatings. Materials Sciences and Applications, 6, 9-15. doi: 10.4236/msa.2015.61002.
References
[1]   Bruno, F., Friedrich, C. and Warrington, R.O. (1995) The Miniturization Technologies: Past, Present, and Future. IEEE Transactions on Industrial Electronics, 42, 423-430.
http://dx.doi.org/10.1109/41.464603

[2]   Williams, R.E., Huang, Y., Melkote, S., Kinsey, B., Sun, W. and Yao, D. (2005) Recent Advances in Micro/Meso-Scale Manufacturing Processes. ASME 2005 International Mechanical Engineering Congress and Exposition, Orlando, 5-11 November 2005, ICMECE2005-79889.

[3]   Liu, X., Devor, R.E., Kapoor, S.G. and Ehmann, K.F. (2004) The Mechanics of Machining at The Microscale: Assessment of The Current State of The Science. ASME Journal of Manufacturing Science and Engineering, 126, 666-678.
http://dx.doi.org/10.1115/1.1813469

[4]   Kobayashi, A. (2005) The Features and Application of UPC Nano-Micro Forming Tools. Industrial Diamond Review, 65, 28-30.

[5]   Damazo, B.N., Davies, M.A., Dutterer, B.S. and Kennedy, M.D. (1999) A Summary of Micro-milling Studies. First International Conference and General Meeting of the European Society of Precision Engineering and Nanotechnology, Bremen, 30 May-4 June 1999, 322-325.

[6]   Friedrich, C., Coane, P., Goettert, J. and Gopinathin, N. (1998) Direct Fabrication of Deep X-Ray Lithography Masks by Micromechanical Milling. Precision Engineering, 22, 164-173.
http://dx.doi.org/10.1016/S0141-6359(98)00012-9

[7]   Kim, C.-J., Bono, M. and Ni, J. (2002) Experimental Analysis of Chip Formation in Micro-Milling. Technical Paper Society of Manufacturing Engineers, MR02-159.

[8]   Jackson, M.J., Robinson, G.M. and Ahmed, W. (2006) Micromachining Selected Metals Using Diamond Coated Cutting Tools. International Journal of Nanomanufacturing, 1, 304-317.
http://dx.doi.org/10.1504/IJNM.2006.012201

[9]   Isomura, K., Murayama, M., Yamaguchi, H., Ijichi, N., Saji, N., Shiga, O., Takahashi, K., Tanaka, S., Genda, T. and Esashi, M. (2003) Development of Micro-Turbo Charger and Micro-Combustor as Feasibility Studies of Three-Dimensional Gas Turbine at Micro-Scale. ASME Turbo Expo 2003, Collocated with the 2003 International Joint Power Generation Conference, Atlanta, 16-19 June 2003, 685-690.
http://dx.doi.org/10.1115/GT2003-38151

[10]   Jeon, Y. and Pfefferkorn, F.E. (2007) Laser-Assisted Machining of Silicon Nitride with Cubic Boron Nitride Tipped Micro End Mill. Second International Conference on Micro-Manufacturing, South Carolina, 43.

[11]   Robertson, J. (2002) Diamond-Like Amorphous Carbon. Materials Science and Engineering Reports, 37, 129-281.
http://dx.doi.org/10.1016/S0927-796X(02)00005-0

[12]   Cho, S.-J., Chung, J.-W. and Lee, K.-R. (2005) Characterization of the Mechanical Properties of Diamond-Like Carbon Films. Diamond and Related Materials, 14, 1270-1276.
http://dx.doi.org/10.1016/j.diamond.2004.11.034

[13]   Singh, R.A., Yoon, E.-S., Kim, H.J., Kong, H., Park, S.-J. and Lee, K.-R. (2006) Friction Behaviour of Diamond-Like Carbon Films with Varying Mechanical Properties. Surface and Coatings Technology, 201, 4348-4351.
http://dx.doi.org/10.1016/j.surfcoat.2006.08.055

[14]   Cotell, C.M. and Hirvonen, J.K. (1996) Effect of Ion Energy on The Mechanical Properties of Ion Beam Assisted Deposition (IBAD) Wear Resistant Coatings. Surface and Coatings Technology, 81, 118-125.
http://dx.doi.org/10.1016/0257-8972(95)02650-9

[15]   Noshiro, J., Watanabe, S., Sakurai, T. and Miyake, S. (2006) Friction Properties of Co-Sputtered Sulfide/DLC Solid Lubricating Films. Surface and Coatings Technology, 200, 5849-5854.
http://dx.doi.org/10.1016/j.surfcoat.2005.08.147

[16]   Ikeyama, M., Miyagawa, S., Miyagawa, Y., Hayakawa, Y. and Miyajima, T. (2007) DLC Coatings on Inner Walls of PET Bottles by a Simplified PBII Technique. Surface and Coatings Technology, 201, 8112-8115.
http://dx.doi.org/10.1016/j.surfcoat.2006.02.064

[17]   Günther, M., Bialuch, I., Peter, S., Bewilogua, K. and Richter, F. (2011) High Rate Deposition of Hard a-C:H Films Using Microwave Excited Plasma Enhanced CVD. Surface and Coatings Technology, 205, S94-S98.
http://dx.doi.org/10.1016/j.surfcoat.2010.12.047

[18]   Jongwannasiri, C., Moolsradoo, N., Khantachawana, A., Kaewtatip, P. and Watanabe, S. (2012) The Comparison of Biocompatibility Properties between Ti Alloys and Fluorinated Diamond-Like Carbon Films. Advances in Materials Science and Engineering, 2012, 1-8.
http://dx.doi.org/10.1155/2012/724126

[19]   Yang, W.J., Choa, Y.-H., Sekino, T., Shim, K.B., Niihara, K. and Auh, K.H. (2003) Thermal Stability Evaluation of Diamond-Like Nanocomposite Coatings. Thin Solid Films, 434, 49-54.
http://dx.doi.org/10.1016/S0040-6090(03)00466-8

[20]   Yang, S.H., Kong, H., Lee, K.-R., Park, S. and Kim, D.E. (2002) Effect of Environment on the Tribological Behavior of Si Incorporated Diamond-Like Carbon Films. Wear, 252, 70-79.
http://dx.doi.org/10.1016/S0043-1648(01)00856-0

[21]   Saha, B., Liu, E., Tor, S.B., Khun, N.W., Hardt, D.E. and Chun, J.H. (2010) Replication Performance of Si-N-DLC-Coated Si Micro-Molds in Micro-Hot-Embossing. Journal of Micromechanics and Microengineering, 20, 1-8.
http://dx.doi.org/10.1088/0960-1317/20/4/045007

[22]   Jongwannasiri, C., Li, X. and Watanabe, S. (2013) Improvement of Thermal Stability and Tribological Performance of Diamond-Like Carbon Composite Thin Films. Materials Sciences and Applications, 4, 630-636.
http://dx.doi.org/10.4236/msa.2013.410077

[23]   Sui, J.H. and Cai, W. (2007) Mechanical and Corrosion Study of Diamond-Like Carbon Coating on NiTi Alloys. Surface and Coatings Technology, 201, 5121-5123.
http://dx.doi.org/10.1016/j.surfcoat.2006.07.225

 
 
Top