Thermal Distribution Performance of NPCM: NaCl, NaNO3 and KNO3 in the Thermal Storage System

Pises  Tooklang; Sarayooth  Vaivudh; Sukrudee  Sukchai; Wattanapong  Rakwichian

doi:10.4236/epe.2014.67016

Pises Tooklang^*, Sarayooth Vaivudh, Sukrudee Sukchai, Wattanapong Rakwichian

Abstract: The experiment is studied on thermal distribution in the thermal energy storage system with non-phase change materials (NPCM): NaNO3, KNO3 and NaCl in the range of 25°C - 250°C. The cylindrical storage system was made of stainless steel with 25.6 cm-diameter and 26.8 cm-height that was contained of these NPCM. There was one pipe for heat transfer fluid (HTF) with 1.27 cm-diameter that manipulates in the storage tank and submerges to NPCM. The inner pipe was connected to the 2.27 cm-diameter outer HTF tube. The tube was further connected to the thermal pump, heater and load. The pump circulates the synthetic oil (Thermia oil) within the pipe for heat transferring purposes (charging and discharging). An electric heater is used as the heat source. The limitation of the charging oil temperature is maintained at 250°C with the flow rates in the range of 0.58 to 1.45 kg/s whereas the inlet temperature of the discharge oil is maintained at 25°C. Thermal performances of TES (thermal energy storage) such as charging and discharging times, radial thermal distribution, energy storage capacity and energy efficiency have been evaluated. The experimental results show that the radial thermal distribution of NaCl for TR inside, TR middle and TR outside was optimum of temperature down to NaNO3 and KNO3 respectively. Comparison of NPCMs with oil, flow rates for NaCl were charging and discharging heat transfer than KNO3 and NaNO3. The thermal stored NaCl ranged from 5712 - 5912 J; KNO3 ranged from 7350 - 7939 J and NaNO3 ranged from 6623 - 6930 J respectively. The thermal energy stored for experimental results got with along the KNO3, NaNO3 and NaCl respectively. The thermal energy efficiency of NaCl, KNO3 and NaNO3 was in the range 66% - 70%.

Keywords: Thermal Distribution, Non-Phase Change Materials, Heat Transfer Fluid, Thermal Energy Storage, Thermal Performance

Cite this paper: Tooklang, P. , Vaivudh, S. , Sukchai, S. and Rakwichian, W. (2014) Thermal Distribution Performance of NPCM: NaCl, NaNO₃ and KNO₃ in the Thermal Storage System. Energy and Power Engineering, 6, 174-185. doi: 10.4236/epe.2014.67016.

References

[1] Vaivudh, S., Rakwichian, W., Chindaruksa, S. and Sriprang, N. (2006) Heat Transfer of Charging and Discharging Experiment of High Thermal Energy Storage System by Thermal Oil as Heat Transfer Fluid. International Journal of Renewable Energy, 1, 17-21.
http://www.sert.nu.ac.th/IIRE/V1N2(3).pdf

[2] Abhat, A. (1983) Low Temperature Latent Heat Thermal Energy Storage: Heat Storage Materials. Solar Energy, 30, 313-332.
http://dx.doi.org/10.1016/0038-092X(83)90186-X

[3] Soontornchainacksaeng, T. (2005) Experimentation and Simulation of Thermal Energy Storage System with Non-Phase Change Materials. Journal of Mechanical Engineering, 50, 534-537.

[4] Somasundaram, S., Drost, M.K., Brown, D.R. and Antoniak, Z.I. (1993) Integrating Thermal Energy Storage in Power Plants. International Journal of Mechanical Engineering, 84-90.

[5] Soontornchainacksaeng T. and Tontiwongwatana, J. (1996) Simulation of Thermal Energy Storage with Water. Department of Mechanical Engineering, Faculty of Engineering, King Mongkut’s Institute of Technology North Bangkok, Bangkok.

[6] Michels, H. and Pitz-Paal, R. (2007) Cascaded Latent Heat Storage for Parabolic Trough Solar Power Plants. Solar Energy, 81, 829-837.
http://dx.doi.org/10.1016/j.solener.2006.09.008

[7] Banaszek, J., et al. (1999) Experimental Study of Solid-Liquid Phase Change in a Spiral Thermal Energy Storage Unit. Applied Thermal Engineering, 19, 1253-1277.
http://dx.doi.org/10.1016/S1359-4311(98)00120-3

[8] Khot, S.A., Sane, N.K. and Gawali, B.S. (2011) Experimental Investigation of Phase Change Phenomena of Paraffin Wax inside a Capsule. International Journal of Engineering Trends and Technology, 2, 67-71.
http://www.ijettjournal.org/archive/ijett-v2i2p213

[9] Dietz, D. (1984) Thermal Performance of a Heat Storage Module Using Calcium Chloride Hexahydrate. Journal of Solar Energy Engineering, 106, 106-111.
http://dx.doi:10.1115/1.3267552

[10] Regin, A. F., Solanki, S.C. and Saini, J.S. (2006) Experimental and Numerical Analysis of Melting of PCM inside a Spherical Capsule. Proceedings of Thermophysics and Heat Transfer Conference, San Francisco, 5-8 June 2006, 2006-3618.

[11] Roy, S.K. and Sengupta S. (1990) Gravity-Assisted Melting in a Spherical Enclosure: Effects of Natural Convection. International Journal of Heat and Mass Transfer, 33, 1135-1147.
http://dx.doi.org/10.1016/0017-9310(90)90246-Q

[12] Khodadadi, J.M. and Zhang, Y. (2001) Effects of Buoyancy-Driven Convection on Melting Within Spherical Containers. International Journal of Heat and Mass Transfer, 44, 1605-1618.
http://dx.doi.org/10.1016/S0017-9310(00)00192-7

[13] Shell Company (2010) Shell Heat Transfer Oil S2 High Performance Heat Transfer Fluid.
http://s02.static-shell.com/content/dam/shell/static/ind/downloads/lubes-b2b/other-shell-
lubricants/heat-transfer-oil.pdf