Back
 GM  Vol.4 No.1 , January 2014
Hole Cleaning Prediction in Foam Drilling Using Artificial Neural Network and Multiple Linear Regression
Abstract: Foam drilling is increasingly used to develop low pressure reservoirs or highly depleted mature reservoirs because of minimizing the formation damage and potential hazardous drilling problems. Prediction of the cuttings concentration in the wellbore annulus as a function of operational drilling parameters such as wellbore geometry, pumping rate, drilling fluid rheology and density and maximum drilling rate is very important for optimizing these parameters. This paper describes a simple and more reliable artificial neural network (ANN) method and multiple linear regression (MLR) to predict cuttings concentration during foam drilling operation. This model is applicable for various borehole conditions using some critical parameters associated with foam velocity, foam quality, hole geometry, subsurface condition (pressure and temperature) and pipe rotation. The average absolute percent relative error (AAPE) between the experimental cuttings concentration and ANN model is less than 6%, and using MLR, AAPE is less than 9%. A comparison of the ANN and mechanistic model was done. The AAPE values for all datasets in this study were 3.2%, 8.5% and 10.3% for ANN model, MLR model and mechanistic model respectively. The results show high ability of ANN in prediction with respect to statistical methods.
Cite this paper: R. Rooki, F. Doulati Ardejani and A. Moradzadeh, "Hole Cleaning Prediction in Foam Drilling Using Artificial Neural Network and Multiple Linear Regression," Geomaterials, Vol. 4 No. 1, 2014, pp. 47-53. doi: 10.4236/gm.2014.41005.
References

[1]   T. Zhu, L. Volk and H. Carroll, “Industry State-of-the-Art in Underbalanced Drilling,” Project Report, 1995.

[2]   R. Wang, R. Cheng, H. Wang and Y. Bu, “Numerical Simulation of Transient Cuttings Transport with Foam Fluid in Horizontal Wellbore,” Journal of Hydrodynamics, Vol. 21, No. 4, 2009, pp. 437-444.
http://dx.doi.org/10.1016/S1001-6058(08)60169-9

[3]   T. Nazari, G. Hareland and J. J. Azar, “Reviw of Cuttings Transport in Directional Well Drilling, Systematic Approach,” SPE 132372, California, 2010.

[4]   T. I. Larsen, A. A. Pilehvari and J. J. Azar, “Development of a New Cutting Transport Model for High Angle Well- bores Including Horizontal Wells,” SPE Drilling and Completion, Vol. 12, No. 2, 1997, pp. 129-136.
http://dx.doi.org/10.2118/25872-PA

[5]   M. Yu, N. E. Takach, D. R. Nakamura and M. M. Shariff, “An Experimental Study of hole Cleaning under Simulated Downhole Conditions,” Saudi Aramco of Technology, 2007, pp. 2-16.

[6]   B. V. Loureiro, R. S. de Paula and M. B. Serafim, “Experimental Evaluation of the Effect of Drillstring Rotation in the Suspension of a Cuttings Bed,” SPE Latin American and Caribbean Petroleum Engineering Conference, Lima, 1-3 December 2010, 14 p.
http://dx.doi.org/10.2118/122071-MS

[7]   M. E. Ozbayoglu, S. Z. Miska, T. Reed and N. Takach, “Using foam in Horizontal Well Drilling, a Cuttings Transport Modeling Approach,” Journal of Petroleum Science and Engineering, Vol. 46, No. 4, 2005, pp. 267-282. http://dx.doi.org/10.1016/j.petrol.2005.01.006

[8]   Z. Chen, “Cuttings Transport with Foam in Horizontal Concentric Annulus under Elevated Pressure and Temperature Conditions,” Ph.D. Thesis, Tulsa University, Tulsa, 2005.

[9]   M. Duan, “Study of Cuttings Transport Using Foam with Drill Pipe Rotation under Simulated Downhole Conditions,” Ph.D. Thesis, Tulsa University, Tulsa, 2007.

[10]   S. Saintpere, Y. Marcillat, F. Bruni and A. Toure, “Hole Cleaning Capabilities of Drilling Foams Compared to Conventional Fluids,” SPE Annual Technical Conference and Exhibition, Texas, 2000.

[11]   A. L. Martins, A. M. F. Luorenco and C. H. M. de Sa, “Foam Properties Requirements for Proper Hole Cleaning While Drilling Horizontal Wells in Underbalanced Conditions,” SPE Drilling and Completion, Vol. 16, No. 4, 2001, pp.195-200. http://dx.doi.org/10.2118/74333-PA

[12]   Y. Li and E. Kuru, “Numerical Modeling of Cuttings Transport with Foam in Horizontal Wells,” Journal of Canadian Petroleum Technology, Vol. 42, No. 10, 2003, pp. 54-61. http://dx.doi.org/10.2118/03-10-06

[13]   Y. Li and E. Kuru, “Numerical Modeling of Cuttings Transport with Foam in Vertical Wells,” Journal of Canadian Petroleum Technology, Vol. 44, No. 3, 2005, pp. 31-39.

[14]   J. Capo, M. Yu, S. Z. Miska, N. E. Takach and R. Ahmed, “Cuttings Transport with Aqueous foam at Intermediate Inclined Wells,” SPE Drilling and Completion, Vol. 21, No. 2, 2006, pp. 99-107.
http://dx.doi.org/10.2118/89534-PA

[15]   Z. Chen, R. M. Ahmed, S. Z. Miska, N. E. Takach, M. Yu, M. B. Pickell and J. Hallman, “Experimental study on cuttings transport with foam under simulated horizontal downhole conditions,” SPE Drilling and Completion, Vol. 22, No. 4, 2007, pp. 304-312.
http://dx.doi.org/10.2118/99201-PA

[16]   M. Duan, S. Miska, M. Yu, N. Takach, R. Ahmed and J. Hallma, “Experimental Study and Modeling of Cuttings Transport Using Foam with Drillpipe Rotation,” SPE Drilling and Completion, Vol. 25, No. 3, 2010, pp. 352-362. http://dx.doi.org/10.2118/116300-PA

[17]   H. Demuth and M. Beale, “Neural Network Toolbox for Use with MATLAB,” Handbook, 2002.

[18]   S. Haykin, “Neural Networks: A Comprehensive Foundation,” 2nd Edition, Prentice Hall, Upper Saddle River, 1999.

[19]   M. T. Hagan, H. B. Demuth and M. H. Beale, “Neural network design,” PWS Publishing, Boston, 1996.

[20]   J. Ternyik, H. I. Bilgesu and S. Mohaghegh, “Virtual Measurements in Pipes: Part 2, Liquid Holdup and Flow Pattern Correlations,” SPE Eastern Regional Conference & Exhibition, Morgantown, 18-20 September 1995, 5 p.

[21]   M. E. Ozbayoglu, S. Z. Miska, T. Reed and N. Takach, “Analysis of Bed Height in Horizontal and Highly-Inclined Wellbores by Using Artificial Neural Networks,” International Horizontal Well Technology Conference, Calgary, 4-7 November 2002, 7 p.

[22]   E. S. A. Osman, “Artificial Neural Network Models for Identifying Flow Regimes and Predicting Liquid Holdup in Horizontal Multiphase Flow,” SPE Production & Facilities, Vol. 19, No. 1, 2004, pp. 33-40.
http://dx.doi.org/10.2118/86910-PA

[23]   M. E. Shippen and S. L. Scott, “A Neural Network Model for Prediction of Liquid Holdup in Two-Phase Horizontal Flow,” SPE Production & Facilities, Vol. 19, No. 2, 2004, pp. 67-76.
http://dx.doi.org/10.2118/87682-PA

[24]   E. M. Ozbayoglu and M. A. Ozbayogl, “Estimating Flow Patterns and Frictional Pressure Losses of Two-Phase Fluids in Horizontal Wellbores Using Artificial Neural Networks,” Petroleum Science and Technology, Vol. 27, No. 2, 2009, pp. 135-149.
http://dx.doi.org/10.1080/10916460701700203

[25]   R. Ashena and J. Moghadasi, “Bottom Hole Pressure Estimation Using Evolved Neural Networks by Real Coded Ant Colony Optimization and Genetic Algorithm,” Journal of Petroleum Science and Engineering, Vol. 77, No. 3-4, 2011, pp. 375-385.
http://dx.doi.org/10.1016/j.petrol.2011.04.015

[26]   A. E. F. Monfared, M. Ranjbar, H. Nezamabadi Pour, M. Schaffie and R. Ashena, “Substantial Improvement of the Bottom Hole Circulating Pressure Prediction by the Combination of GA and ANFIS,” Energy Source Part A, Vol. 33, No. 24, pp. 2272-2280.

[27]   R. Rooki, F. Doulati Ardejani, A. Moradzadeh, V. C. Kelessidis and M. Nourozi, “Prediction of Terminal Velocity of Solid Spheres Falling through Newtonian and Non-Newtonian Power Law Pseudoplastic Fluid Using Artificial Neural Network,” International Journal of Mineral Processing, Vol. 110-111, 2012, pp. 53-61.
http://dx.doi.org/10.1016/j.minpro.2012.03.012

[28]   G. Cybenko, “Approximation by Superposition of a Sigmoidal Function,” Mathematics of Control, Signals and Systems, Vol. 2, No. 4, 1989, pp. 303-314.
http://dx.doi.org/10.1007/BF02551274

[29]   K. Hornik, M. Stinchcombe and H. White, “Multilayer Feed Forward Networks Are Universal Approximates,” Neural Networks, Vol. 2, No. 5, 1989, pp. 359-366.
http://dx.doi.org/10.1016/0893-6080(89)90020-8

[30]   D. Fletcher and E. Goss, “Forecasting with Neural Networks: An Application Using Bankruptcy Data,” Inform Manage, Vol. 24, No. 3, 1993, pp. 159-167.

 
 
Top