MSCE  Vol.1 No.5 , October 2013
The Heat Treatment Behavior of Super-High Strength Aluminum Alloys by Spray Forming
ABSTRACT

In order to understand the stress corrosion behavior of super-high strength aluminum alloys by spray forming, different aluminum alloys by different heat treatment was made. The results showed that the alloy with peak aging has the most sensitive stress corrosion cracking, the crack can even be seen using eyes; the alloys with two step aging were better than one step aging alloys, the alloys has not been found stress corrosion cracking.


Cite this paper
Zhang, G. , Chen, Z. , Zhu, X. , Chen, G. , Zhai, J. and Guo, A. (2013) The Heat Treatment Behavior of Super-High Strength Aluminum Alloys by Spray Forming. Journal of Materials Science and Chemical Engineering, 1, 57-60. doi: 10.4236/msce.2013.15012.
References
[1]   S. D. Liu, X. M. Zhang and M. A. Chen, “Effect of Zr Content on Quench Sensitivity of AlZnMgCu Alloys,” Transactions of Nonferrous Metals Society of China, Vol. 17, 2007, pp. 787-792. http://dx.doi.org/10.1016/S1003-6326(07)60175-7

[2]   C. Mondal, A. K. Mukhopadhyay, T. Raghu and V. K. Varma, “Tensile Properties of Peak Aged 7055 Aluminum Alloy Extrusions,” Materials Science and Engineering: A, Vol. 455, No. 3, 2007, p. 673. http://dx.doi.org/10.1016/j.msea.2006.10.138

[3]   M. Dixit, R. S. Mishra and K. K. Sankaran, “Structure-Property Correlations in Al 7050 and Al 7055 High-Strength Aluminum Alloys,” Materials Science and Engineering: A, Vol. 478, No. 1-2, 2008, p. 163. http://dx.doi.org/10.1016/j.msea.2007.05.116

[4]   Z. H. Li, B. Q. Xiong, Y. A. Zhang, et al., “Ageing Behavior of an Al-Zn-Mg-Cu Alloy Pre-Stretched Thick Plate,” Journal of University of Science and Technology Beijing, Vol. 14, No. 3, 2007, p. 246. http://dx.doi.org/10.1016/S1005-8850(07)60047-4

[5]   K. H. Chen, H. W. Liu, Z. Zhang, et al., “The Improvement of Constituent Dissolution and Mechanical Properties of 7055 Aluminum Alloy by Stepped Heat Treatments,” Journal of Materials Processing Technology, Vol. 142, No. 1, 2003, p. 190. http://dx.doi.org/10.1016/S0924-0136(03)00597-1

[6]   R. C. Dorward and D. J. Beerntsen, “Grain Structure and Quench-Rate Effects on Strength and Toughness of AA7050 Al-Zn-Mg-Cu-Zr Alloy,” Metallurgical and Materials Transactions A, Vol. 26, 1995, pp. 2481-2484. http://dx.doi.org/10.1007/BF02671263

[7]   M. Sharma, M. Amateau and T. Eden, “Mesoscopic Structure Control of Spray Formed High Strength Al-Zn-Mg-Cu Alloys,” Acta Materialia, Vol. 53, 2005, pp. 2919-2924. http://dx.doi.org/10.1016/j.actamat.2005.03.007

[8]   M. Sharma, M. Amateau and T. Eden, “Hardening Mechanisms of Spray Formed Al-Zn-Mg-Cu Alloys with Scandium and Other Elemental Additions,” Journal of Alloys and Compounds, Vol. 416, 2006, 135-142. http://dx.doi.org/10.1016/j.jallcom.2005.08.045

[9]   R. Machler, P. Uggowitzer, C. Solenthaler, R. Pedrazzoli and M. Speidel, “Structure, Mechanical Properties, and Stress Corrosion Behavior of High Strength Spray Deposited 7000 Series Aluminum Alloy,” Materials Science and Technology, Vol. 7, 1991, pp. 447-451. http://dx.doi.org/10.1179/026708391790183880

[10]   M. DeSanctis, “Structure and Properties of Rapidly Solidified Ultrahigh Strength Al-Zn-Mg-Cu Alloys Produced by Spray Deposition,” Materials Science and Engineering: A, Vol. 141, 1991, pp. 103-121.

 
 
Top