OJOPM  Vol.3 No.4 , October 2013
Influence of Poly(vinyl chloride) on Natural Rubber/Chlorosulfonated Polyethylene Blends
Abstract: Blend of natural rubber (NR) and chlorosulfonated polyethylene (CSM) was so interesting due to binding of the good oil resistance of CSM, the good mechanical properties and low cost of NR. However, due to the different polarities of two rubbers, phase separation and inferior properties of NR/CSM blend were obtained. The practical way to improve its properties is the addition of the third component to bind both phases of the blend. Effects of poly(vinyl chloride), PVC as compatibilizer on cure characteristics, morphology, mechanical properties and automotive fuel resistance of NR/ CSM blend were investigated. In this contribution, NR/CSM blend with blend ratio of 50/50 was prepared using a two-roll mill, and then vulcanized in a compression mold at 160°C. The PVC content was varied from 1 to 7 phr. It was found that the usage of 7 phr PVC led to improve interaction between NR and CSM phases. Therefore, increase in cure characteristics, mechanical strength and automotive fuel resistance of the blend was observed.
Cite this paper: M. Phiriyawirut and S. Luamlam, "Influence of Poly(vinyl chloride) on Natural Rubber/Chlorosulfonated Polyethylene Blends," Open Journal of Organic Polymer Materials, Vol. 3 No. 4, 2013, pp. 81-86. doi: 10.4236/ojopm.2013.34013.

[1]   D. J. Zanzig, F. L. Magnus, W. L. Hsu, A. F. Halasa and M. E. Testa, “IBR Block Copolymers as Compatibilizers in NR/BR Blends,” Rubber Chemistry and Technology, Vol. 66, No. 4, 1993, pp. 538-549.

[2]   R. Holsti-Miettinen, J. Seppala and O. T. Ikkala, “Effects of Compatibilizers on the Properties of Polyamide/Polypropylene Blends,” Polymer Engineering & Science, Vol. 32, No. 13, 1992, pp. 868-877.

[3]   S. H. EL-Sabbagh, “Compatibility Study of Natural Rubber and Ethylene-Propylene-Diene Rubber Blends,” Journal of Applied Polymer Science, Vol. 90, No. 1, 2003, pp. 1-11.

[4]   M. T. Ramesan, “Thermogravimetric Analysis, Flammability and Oil Resistance Properties in Natural Rubber and Dichlorocarbene Modified Styrene Butadiene Rubber Blends,” Reactive and Functional Polymers, Vol. 59, No. 3, 2004, pp. 267-274.

[5]   K. Saguan, T. Suteewong, P. Saendee, U. Buranabunya and P. Tangboriboonrat, “Composite Natural Rubber Based Latex Particles: A Novel Approach,” Polymer, Vol. 46, No. 4, 2005, pp. 1373-1378.

[6]   A. Y. Coran and R. Patel, “Rubber-Thermoplastic Com- positions 1. EPDM-Polypropylene Thermoplastic Vulcanizates,” Rubber Chemistry and Technology, Vol. 53, No. 1, 1980, pp. 141-150.

[7]   A. P. Plochocki, S. S. Dagli and R. D. Andrews, “Interface in Binary Mixtures of Polymers Containing a Corresponding Block Copolymer. Effects of Industrial Mixing Processes and of Coalescence,” Polymer Engineering and Science, Vol. 30, No. 12, 1990, pp. 741-752.

[8]   H. Ismail and H. M Hairunezam, “The Effect of a Compatibilizer on Curing Characteristics, Mechanical Properties and Oil Resistance of Styrene Butadiene Rubber/Epoxidized Natural Rubber Blends,” European Polymer Journal, Vol. 37, No. 1, 2001, pp. 39-44.

[9]   K. Pielichowski and I. Hamertor, “Compatible Poly(vinyl chloride)/Chlorinated Polyurethane Blend: Thermal Characteristics,” European Polymer Journal, Vol. 36, No. 1, 2004, pp. 171-181.

[10]   C. Sirisinha, P. Saeouic and J. Guaysomboona, “Oil and Thermal Aging Resistance in Compatibilized and Thermally Stabilized Chlorinated Polyethylene/Natural Rubber Blends,” Polymer, Vol. 45, No. 14, 2004, pp. 4909- 4915.