Back
 EPE  Vol.5 No.4 B , July 2013
Cold-state Experimental Study on Flow Characteristics of Multi-nozzle in Natural Gas Reburning Burner
Abstract: Based on the prototypes of a 130 t/h boiler, constant proportional cold-state test bench is established, flow characteristics of multi-nozzle in natural gas reburning burner and its influence on the covering effect for the upflow in the furnace are researched. Numerical simulations of this process are also made with standard  turbulence model. The results show that air flow fullness in furnace is better in the case of the reburning zone with 8 nozzles compared to 4 nozzles and also coverage effect of the reburning flow for the updraft gas in the furnace is better. In the condition each nozzle airflow velocity is constant, the effect of reburning flow on coverage of up-secondary air is best when the incident angle for four corners is 14.17?, while Center of the furnace wall is 84.57. And while the best incident angle is invariable, the effect of reburning flow on coverage of up-secondary air is best when the speed of reburning gas in the corners of furnace is 51 m/s, the same to the center of the furnace wall’s.
Cite this paper: B. Chen, Z. Zhang and D. Bi, "Cold-state Experimental Study on Flow Characteristics of Multi-nozzle in Natural Gas Reburning Burner," Energy and Power Engineering, Vol. 5 No. 4, 2013, pp. 324-329. doi: 10.4236/epe.2013.54B064.
References

[1]   J. Mereb and J. O. L. Wendt, “Reburning Mechanism in pulverized Coal Combustor,” Twenty-third Symposium (international) on Combustion Institute, 1990, pp. 1273-1304.

[2]   M. Patry and G. Engel, “Formation of HCN by the Action of Nitric Oxide on Methane Atatmospheric Pressure, General Conditions of Formation. Compt. Rend, Vol. 231, 1950, pp. 1302-1304

[3]   X. D. Yao, Z. X. Zhang, L. L. Qiu, et al., “Analysis on the Kinetic Mechanism and Key Parameters of NO_x Reduction with Natural Gas Reburning,” Journal of University of Shanghai For Science and Technology, Vol. 26, No. 1,2004, pp. 62-65.

[4]   Z. G. Li, “Similar and Modeling,” Beijing: National Defence Industry Press, 1982.

[5]   K. F. Cen, “research method and measurement technology for Boiler combustion experimental [M]. Water Conservancy and Electric Power Press, 1987.

[6]   Q. Guo, W. J. Ma and R. Sun, “Experimental Study on Furnace Air Flow Field of a 2000t/h Tangentially Fired Boiler,” Power System Engineering, 2010.

[7]   W. Q. Tan, “Numerical Heat Transfer (version 2),” Xi'an: Xi'an Jiaotong University Press,2001.

[8]   Z. H. Tuo, Z. Hang, X. Zhong, X. J. Wu, et al., “Study on Flow Characteristics of Nozzle in Gas-reburning burner,” Journal of University of Shanghai For Science and Technology, Vol. 29, No. 2, 2007, pp. 137-141.

[9]   Z. Y. Dong, “Jet Theory of Fluid Mechanics, beijing:Science press,2005

[10]   S. Y. Wu, Y. R. Li, X. F. Lu, et al., “Cold State Analysis on the Jet of Single Nozzle Using Gas-reburning for NOx Reduction,” Industrial Heating, Vol. 6, 2001, pp. 4-7.

[11]   Y. Wang, Y. K. Qin, S. H. Wu, et al., “Numerical Simulation and A nalysis of the Effect of an Infurnace Flow Field on the High Temperature Corrosion of Water Walls in a Tangentially Fired Boiler Fur n ace,” Journal of Engineering for Thermal Energy and Power, Vol. 15, No. 87, 2000, pp. 284-329.

[12]   T. Zhu, W. D. Fan, et al., “A Numerical Simulation Study of Aerodynamic Field Characteristics in a Double Furnace,” Journal of Engineering for Thermal Energy and Power, Vol. 12, No. 06, 1997, pp. 401-477.

 
 
Top