ENG  Vol.2 No.11 , November 2010
Design and Modeling of Femto Air Bearing Slider
Abstract
This paper presents the studies of the performance of an improved femto air bearing slider which is optimized based on the past studies and effort. The flying characteristics performance of this novel femto slider is relatively stable over different radii. This optimized slider achieved a flying height of 3 nm, with variation of about 0.2 nm. The variations for pitch and roll values are 6 µrad and 0.9 µrad respectively. In the studies for the effect of side rail on flying characteristics, it was found that there exists transition of pitch value when the side rail is located very close to the leading edge. The modulation of flying height reduces greatly when the areas of double shallow steps increase. The roll variation reduces when the flat double shallow steps profile is modified into a “V-Shape” profile.

Cite this paper
nullC. Yong, E. Ng, W. Zhou and W. Ng, "Design and Modeling of Femto Air Bearing Slider," Engineering, Vol. 2 No. 11, 2010, pp. 841-854. doi: 10.4236/eng.2010.211107.
References

[1]   B. Liu, M. Zhang, S. Yu, G., Leonard, Y. S., Hor and J. Xu, “Femto Slider Fabrication and Evaluation,” Asia- Pacific Magnetic Recording Conference 2002 and IEEE Transactions on Magnetics, Vol. 39, No. 2, 2003, pp. 909-914.

[2]   D. S. Chabra, S. A. Bolasna, L. K. Dorius and L. S. Samuelson, “Air Bearing Design Considerations for Constant Flying Height Applications,” IEEE Transactions on Magnetics, Vol. 30, No. 2, 1994, pp. 417-423.

[3]   Y. Wada, T. Roppongi and I. Sato, “Flying Characteristics of Shallow Step Pads Slider for Low Flying,” IEEE Transactions on Magnetics, Vol. 35, No. 5, 1999, pp. 2475-2477.

[4]   S. Lu, Y. Hu, M. O’Hara and D. B. Bogy, “Air Bearing Design, Optimization, Stability Analysis and Verification for Sub-25 nm Flying,” IEEE Transactions on Magnetics, Vol. 32, No. 1, 1996, pp. 103-108.

[5]   J. K. Lee, J. Enguero, M. Smallen and A. Chao, “The Influence of Head Parameters on Take-off Velocity,” IEEE Transactions on Magnetics, Vol. 29, No. 6, 1993, pp. 3915-3917.

[6]   B. H. Thornton, A. Nayak and D. B. Bogy, “Flying Height Modula-tion due to Disk Waviness of sub-5 nm Flying Height Air Bearing Sliders,” Journal of Tribology, Vol. 124, No. 4, 2002, pp. 762-770.

[7]   J. Xu and B. Liu, “Flying Height Modulation and Femto Slider Design,” IEEE Transactions on Magnetics, Vol. 39, No. 5, 2003, pp. 2438-2440.

[8]   Q.-H. Zeng and D. B. Bogy, “Slider Air Bearing Designs for Load/Unload,” IEEE Transactions on Magnetics, Vol. 35, No. 2, 1999, pp. 746-751.

[9]   K. S. Park, J. I. Chun, Y. H. Lee, N. C. Park, H. S. Yang and Y. P. Park, “Improvement of Loading/Unloading Performance Using Control Input Position and Considering Disk Vibration Characteristics,” IEEE Transactions on Mag-netics, Vol. 41, No. 2, 2005, pp. 819-824.

[10]   T. G. Jeong and D. B. Bogy, “Measurements of Slider- Disk Contacts during Dynamic Load-Unload,” IEEE Transactions on Magnetics, Vol. 27, No. 6, 1991, pp. 5073-5075.

[11]   P. W. Smith and G. L. Best, “Figures of Merit for Dynamically Unloaded Air Bearing Sliders,” Tribology Transactions, Vol. 42, No. 2, 1999, pp. 407-412.

[12]   H. Tanaka, H. Kohira and M. Matsumoto, “Ef-fect of Air-Bearing Design on Slider Dynamics during Un-loading Process,” IEEE Transactions on Magnetics, Vol. 37, No. 4, 2001, pp. 1818-1820.

[13]   S. Weissner, F. Talke, H. Tokisue and J. Xu, “Experimental Comparison of Load/Unload Slider Dynamics for Two Different Pico-Slider Designs,” Tribology Transactions, Vol. 44, No. 4, 2001, pp. 699-703.

[14]   Computer Mechanics Laboratory in the Me-chanical Engineering, “CML Software,” University of California, Berkeley, 2008.

[15]   Q.-H. Zeng and D. B. Bogy, “Effects of Certain Design Parameters on Load/Unload Performance,” IEEE Transactions on Magnetics, Vol. 36, No. 1, 2000, pp. 140-147.

 
 
Top