JBCPR  Vol.1 No.1 , March 2013
Tests on Alkali-Activated Slag Foamed Concrete with Various Water-Binder Ratios and Substitution Levels of Fly Ash
Abstract
To provide basic data for the reasonable mixing design of the alkali-activated (AA) foamed concrete as a thermal insulation material for a floor heating system, 9 concrete mixes with a targeted dry density less than 400 kg/m3 were tested. Ground granulated blast-furnace slag (GGBS) as a source material was activated by the following two types of alkali activators: 10% Ca(OH)2 and 4% Mg(NO3)2, and 2.5% Ca(OH)2 and 6.5% Na2SiO3. The main test parameters were water-to-binder (W/B) ratio and the substitution level (RFA) of fly ash (FA) for GGBS. Test results revealed that the dry density of AA GGBS foamed concrete was independent of the W/B ratio an RFA, whereas the compressive strength increased with the decrease in W/B ratio and with the increase in RFA up to 15%, beyond which it decreased. With the increase in the W/B ratio, the amount of macro capillaries and artificial air pores increased, which resulted in the decrease of compressive strength. The magnitude of the environmental loads of the AA GGBS foamed concrete is independent of the W/B ratio and RFA. The largest reduction percentage was found in the photochemical oxidation potential, being more than 99%. The reduction percentage was 87% - 93% for the global warming potential, 81% - 84% for abiotic depletion, 79% - 84% for acidification potential, 77% - 85% for eutrophication potential, and 73% - 83% for human toxicity potential. Ultimately, this study proved that the developed AA GGBS foamed concrete has a considerable promise as a sustainable construction material for nonstructural element.

Cite this paper
Yang, K. and Lee, K. (2013) Tests on Alkali-Activated Slag Foamed Concrete with Various Water-Binder Ratios and Substitution Levels of Fly Ash. Journal of Building Construction and Planning Research, 1, 8-14. doi: 10.4236/jbcpr.2013.11002.
References

[1]   J.-K. Song and K.-H. Yang, “Development of Environmental-Friendly High-Performance Floor System,” Technical Report, Department of Architectural Engineering, Chonnam National University, Gwangju, 2012.

[2]   E. Gartner, “Industrially Interesting Approaches to ‘Low-CO2’ Cements,” Cement and Concrete Research, Vol. 34, No. 9, 2004, pp. 1489-1498. doi:10.1016/j.cemconres.2004.01.021

[3]   B. L. Damineli, F. M. Kemeid, P. S. Aguiar and V. M. John, “Measuring the Eco-Efficiency of Cement Use,” Cement & Concrete Composite, Vol. 32, No. 8, 2010, pp. 555-562.
doi:10.1016/j.cemconcomp.2010.07.009

[4]   F. Pacheco-Torgal, J. Castro-Gomes and S. Jalali, “Alkali-Activated Binders: A Review-Part 1. Historical Background, Terminology, Reaction Mechanism and Hydration Products,” Construction and Building Materials, Vol. 22, No. 7, 2008, pp. 1305-1314. doi:10.1016/j.conbuildmat.2007.10.015

[5]   P. Duxson, A. Fernández-Jiménez, J. L. Provis, G. C. Lukey, A. Palomo and J. S. J. van Deventer, “Geopolmer Technology: The Current State of the Art,” Journal of Material Science, Vol. 42, No. 9, 2007, pp. 2917-2933. doi:10.1007/s10853-006-0637-z

[6]   C. Shi, P. V. KrddShi and D. Roy, “Alkali-Activated Cements and Concretes,” Taylor and Francis, London, 2006. doi:10.4324/9780203390672

[7]   S. D. Wang, X. C. Pu, K. L. Scrivener and P. L. Pratt, “Alkali-Activated Slag Cement and Concrete: A Review of Properties and Problems,” Advanced Cement Research, Vol. 7, No. 27, 1995, pp. 93-102. doi:10.1680/adcr.1995.7.27.93

[8]   J. Davidovits, “Geopolymer: Chemistry & Applications,” Géopolymère, 2008.

[9]   H. Esmaily and H. Nuranian, “Non-Autoclaved High Strength Cellular Concrete from Alkali Activated Slag,” Construction and Building Materials, Vol. 26, No. 1, 2012, pp. 200-206.
doi:10.1016/j.conbuildmat.2011.06.010

[10]   K.-H. Yang, K.-H. Lee, J.-K. Song and M.-H. Gong, “Development of Alkali-Activated Slag Foamed Concrete for Thermal Insulation,” Cement & Concrete Composite, Submitted for Publication, 2013.

[11]   KS F 2459, F 4039, “Korean Industrial Standard: Testing Concrete,” Korean Standards Information Center (KS), Seoul (in Korean), 2006.

[12]   K. Ramamurthy, E. K. K. Nambiar and G. I. S. Ranjani, “A Classification of Studies on Properties of Foam Concrete,” Cement & Concrete Composite, Vol. 31, No. 6, 2009, pp. 388-396.
doi:10.1016/j.cemconcomp.2009.04.006

[13]   ASTM C796-97, “Annual Book of ASTM Standards: V. 4.02,” ASTM International, 2012.

[14]   D.-H. Lee, M.-H. Jun and J.-S. Ko, “Physical Properties and Quality Control of Foamed Concrete with Fly Ash for Cast-in-Site,” Journal of Korea Concrete Institute, Vol. 13, No. 1, 2001, pp. 69-76 (in Korean).

[15]   ISO 14040, “Environmental Management-Life Cycle Assessment—Principles and Framework,” International Standardisation Organisation 2006.

[16]   Korea LCI Database Information Network, (in Korean). http://www.edp.or.kr/lcidb

[17]   K.-H. Yang, J.-K. Song and K.-I. Song, “Assessment of CO2 Reduction of Alkali-Activated Concrete,” Journal of Cleaner Production, Vol. 39, No. 1, 2013, pp. 265-272. doi:10.1016/j.jclepro.2012.08.001

 
 
Top