JSEA  Vol.6 No.3 , March 2013
Electrical Metrology Applications of LabVIEW Software
ABSTRACT

Automation in measurement has wide range of electrical metrology applications and construction of powerful calibration software is one of the highly accurate metrological laboratories’ priorities. Thus, two automatic systems for controlling and calibrating the electrical reference standards have been established at National Institute for Standards (NIS), Egypt. The first system has been built to calibrate the zener diode reference standards while the second one has been built to calibrate the electrical sourcing and measuring instruments. These two systems act as the comprehensive and reliable structure that, from the national electrical standards, disseminates the traceability to all the electrical units under calibration. The software of the two systems has been built using the Laboratory Virtual Instrument Engineering Workbench (LabVIEW) graphical language. The standard development procedures have been followed in the building of both systems software. The software requirement specifications as well as functional specifications are taken into consideration. Design, implementation and testing of the software have been performed. Furthermore, software validation for measurements’ uncertainty as well as results’ compatibility in both automatic and manual modes has been achieved.


Cite this paper
H. Mageed and A. El-Rifaie, "Electrical Metrology Applications of LabVIEW Software," Journal of Software Engineering and Applications, Vol. 6 No. 3, 2013, pp. 113-120. doi: 10.4236/jsea.2013.63015.
References
[1]   U. Poliano, G. C. Bosco and M. Lanzillotti, “Generalized Automatic System for AC/DC Transfer AC Voltage and AC Current Measurements,” IEEE Transactions on Instrumentation and Measurement, Vol. 55, No. 5, 2006, pp. 1747-1751. doi:10.1109/TIM.2006.880958

[2]   R. Flegar and T. Tasic, “Software Validation in Measurement & Testing,” INCOLAB Conference, Prague, 4 December 2003.

[3]   S. K. Sharma and V. N. Ojha, “Performance Evaluation and Software Validation of Automatic Bank of DC Reference Standard,” Journal of Scientific & Industrial Research, Vol. 64, No. 7, 2005, pp. 487-490.

[4]   http://www.nist.gov/manuscriptpublicationsearch.cfm?pub_id=32563

[5]   S. K. Jaiswal, “Complete Characterization of a Low Thermal Scanner for Automatic Voltage Measurement,” MAPAN-Journal of Metrology Society of India, Vol. 23, No. 1, 2008, pp.31-38

[6]   J. Mountford and G. I. Parkin, “Best Practice in Software Development—A Case Study in LabVIEW Illustrated by the UHTBB Safety System Monitor Project,” NPL Report DEM-ES, Teddington, 2007.

[7]   I. Hadzhieva-Borisova, “Software for Automated AC-DC Measurement System,” International Scientific Conference Computer Science, Sofia, 2008, pp. 528-532

[8]   National Instruments, “LabVIEW Development Guidelines,” 2003.

[9]   National Instruments, “Introduction to LabVIEW,” Part No. 323668B-01, 2003.

[10]   National Instruments, “LabVIEW Quick Start Guid,” Part No. 321527B-01, 1998.

[11]   W. A. Everett, “Calibration: Philosophy in Practice,” 2nd Edition, Fluke Corporation, Everett, 1994.

[12]   United Kingdom Accreditation Service, “The Expression of Uncertainty and Confidence in Measurement,” 2007.

[13]   C. Capua, D. Grillo and E. Romeo, “The Implementation of an Automatic Measurement Station of the Determination of the Calibration Intervals for a DMM,” IEEE International Conference on Virtual Environments, Human-Computer Interfaces and Measurement Systems, Spain, 10-12 July 2006, pp. 58-62.

[14]   Saudi Arabian Standards Organization (SASO), “Guide to the Expression of Uncertainty in Measurement,” 2006.

 
 
Top