AMPC  Vol.3 No.1 , March 2013
Synthesis and Analysis of PZT Using Impedance Method of Reactance Estimation
ABSTRACT
This study presents an analysis of equivalent circuit namely Butterworth Van Dyke (BVD) [1,2] by using impedance method to stimulate Zirconate Titanate (Piezoelectric ceramic) which is initially synthesized from Lead Oxide (PbO), Zirconium Dioxide (ZrO2) and Titanium Dioxide (TiO2) and vibrated in thickness mode. The reactance was estimated in the frequency range lower than the resonance frequency and then compared to the impedance obtained from measurement using impedance analysis machine model HP4192A and HP4194 [3]. The results from HP4194 were analyzed for BVD parameters: Motional resistance (R1), Inductor (L1), Capacitor (C1), and Capacitor corresponds to the electrostatic capacitance (Co). Another accuracy analysis was compared by the calculation results using the method of IEEE 176-1987 [4] to the impedance values measured by HP4192A. In this study, there were two conditions for experiment and consideration of parameter variation in BVD equivalent circuit: variation of temperature and mechanical force. These parameters are evaluated to design the efficient circuit for PZT utilization to obtain the optimal efficiency.

Cite this paper
W. Sriratana, R. Murayama and L. Tanachaikhan, "Synthesis and Analysis of PZT Using Impedance Method of Reactance Estimation," Advances in Materials Physics and Chemistry, Vol. 3 No. 1, 2013, pp. 62-70. doi: 10.4236/ampc.2013.31010.
References
[1]   S. Sherrit, H. D. Wiederick and B. K. Mukherjee, “Accurate Equivalent Circuits for Unloaded Piezoelectric Resonators,” IEEE Ultrasonics Symposium Proceedings, Vol. 2, 1997, pp. 931-935.

[2]   S. Sherrit, H. D. Wiederick, B. K. Mukherjee and M. Sayer, “An Accurate Equivalent Circuits for the Unloaded Piezoelectric Vibrator in the Thickness Mode,” Journal of Physics D: Applied Physics, Vol. 30, No. 16, 1997, pp. 2354-2363. doi:10.1088/0022-3727/30/16/014

[3]   C. Jeerapan, W. Sriratana, P. Julsereewong and S. Kummool, “Analysis of Appropriate Parameters for Piezoelectric Ceramic Utilization by Using BVD Model,” ICCAS 2005, International Conference on Control, Automation and System, Gyeonggi-Do, 2-5 June 2005, pp. 2067-2070.

[4]   “An American National Standard IEEE Standard on Piezoelectricity,” IEEE Ultrasonics, Ferroelectrics, and Frequency Control Society, New York, 1988, ANSI/IEEE Std 176-1987.

[5]   “Standard Definitions and Method of Measurement for Piezoelectric Vibrators,” The Institute of Electrical and Electronics Engineers Inc., New York, 1966, IEEE No. 177.

[6]   J. G. Smits, “Iterative Method for Accurate Determination of Real and Imaginary Parts of the Materials Coefficients of Piezoelectric Ceramics,” IEEE Transactions on Sonics and Ultrasonics, Vol. 23, No. 6, 1976, pp. 393-402. doi:10.1109/T-SU.1976.30898

[7]   S. Sherrit, H. D. Wiederick and B. K. Mukherjee, “NonIterative Evaluation of the Real and Imaginary Material Constants of Piezoelectric Resonators,” Ferroelectrics, Vol. 134, No. 1-4, 1992, pp. 111-119. doi:10.1080/00150199208015574

[8]   Q. C. Xu, A. R. Ramachandran and R. E. Newnham, “Resonance Measuring Technique for Complex Coefficients of Piezoelectric Composites,” Journal of Wave-Material Interaction, Vol. 2, 1987, pp. 105-122.

[9]   B. Jaffe, W. R. Cook Jr and H. Jaffe, “Piezoelectric Ceramics,” Journal of Sound and Vibration, Vol. 20, No. 4, 1972, pp. 562-563.

[10]   T. Ikeda, “Fundamentals of Piezoelectricity,” 19th Edition, Oxford University Press, New York, 1990.

[11]   S. Fujishima, K. Togawa and S. Ohta, “Analysis and Design of the Piezoelectric Ceramic Resonator Osillators,” 41st Annual Symposium on Frequency Control, Pennsylvania, 27-29 May 1987, pp. 391-397. doi:10.1109/FREQ.1987.201052

[12]   M. Trainer, “Ferroelectrics and the Curie-Weiss Law,” European Journal of Physics, Vol. 21, No. 5, 2000, pp. 459-469. doi:10.1088/0143-0807/21/5/312

 
 
Top