JMMCE  Vol.1 No.1 , January 2013
Corrosion Behaviour of Al6061-Frit Particulate Metal Matrix Composites in Sodium Chloride Solution
ABSTRACT
In this investigation, an attempt has been made to develop Al6061-Frit particulate metal matrix composites through stir casting technique using metal molds and to study the corrosion behaviour. Pre heated frit particles were added to matrix as reinforcement. Al6061 containing 2 wt% to 8 wt % in steps of 2 wt % of frit particulate composites were prepared. Corrosion tests were conducted by using Potentiostat model SEP238C where 3.5% NaCl solution was used as corrodent. The corrosion rate of metal matrix composites was lower than that of matrix material Al6061 under the corrosive atmosphere for both un-heat treated and heat treated conditions.

Cite this paper
D. Ramesh, R. Swamy and T. Chandrashekar, "Corrosion Behaviour of Al6061-Frit Particulate Metal Matrix Composites in Sodium Chloride Solution," Journal of Minerals and Materials Characterization and Engineering, Vol. 1 No. 1, 2013, pp. 15-19. doi: 10.4236/jmmce.2013.11003.
References
[1]   B. C. Pai, R. M. Pillai and K. G. Satyanarayana, “Interface in Discontinuous Dispersiod Cast Aluminium Alloy Matrix Composites,” Proceedings of 2nd International Conference on Advances in Composites, Bangalore, 18-20 December 1996, pp. 201-206.

[2]   J. Hashim, L. Looney and M. S. J Hashmi, “Metal Matrix Composites: Production by the Stir Casting Method,” Journal of Materials Processing Technology, Vol. 92-93, No. 30, 1999, pp. 1-7. doi:10.1016/S0924-0136(99)00118-1

[3]   C. S. Ramesh and M. Saffiulla, “Wear Behavior of Hot Extruded Al6061 Based Composites,” Wear, Vol. 263, No. 1-6, 2007, pp. 629-635. doi:10.1016/j.wear.2007.01.088

[4]   P. Rohatgi, “Cast Metal Matrix Composites,” ASM Metal Hand Book, Vol. 15, 1988, pp. 840-854.

[5]   D. M. Skibe, D. M. Sehuster and L. Jolla, “Process for Preparation of Composite Materials Containing Non-Metallic Particles in Metallic Matrix and Composite Materials Made by,” US Patent No. 4.786 467, 1988.

[6]   M. Vogesang, R. J. Arsenault and R. Fisher, “Anin in situ HVEM Study of Dislocation Generation at Al/SiC Interfaces, Metallurgical and Materials Transactions A, Vol. 17, No. 3, 1986, pp. 379-389.

[7]   B. C. Pai, S. Ray, K. V. Prabhakar and P. K. Rohatgi, “Fabrication of Aluminium-Alumina (Magnesia) Particulate Composites in Foundries Using Magnesium Additions to the Melts,” Materials Science and Engineering, Vol. 24, No. 1, 1976, pp. 31-44.

[8]   A. Sato and R. Mehrabia, “Aluminum Matrix Composites: Fabrication & Properties,” Metallurgical and Materials Transactions B, Vol. 7, No. 3, 1976, pp. 443-451.

[9]   S. Samala, A. Bhattaacharyyab and S. K. Mitrab, “Study on Corrosion Behavior of Pearlitic Rail Steel,” Journal of Minerals & Materials Characterization & Engineering, Vol. 10, No. 7, 2011, pp. 573-581.

[10]   K. K. Alaneme and M. O. Bodunrin, “Corrosion Behavior of Alumina Reinforced Aluminium (6063) Metal Matrix Composites,” Journal of Minerals & Materials Characterization & Engineering, Vol. 10, No. 12, 2011, pp. 1153-1165.

[11]   M. A. Bodude, W.A. Ayoola, D. E. Esezobor and A. A. Agbeleye, “Corrosion-Wear of ST60-Mn Steel in Cassava Juice,” Journal of Minerals & Materials Characterization & Engineering, Vol. 11, No. 2, 2012, pp.153-158.

[12]   T. W. Clyne, “Metal Matrix Composites; Matrices and Processing, ‘Composites: MMC, CMC, PMC’”, Elsevier, New York, 2001.

[13]   S. Skolians, (1996), “Mechanical Behavior of Cast SiCp-Reinforced Al-4.5%Cu-1.5% Mg Alloy,” Material Science Engineering, Vol. 210, No. 1-2, 1996, pp. 76-82. doi:10.1016/0921-5093(95)10043-1

[14]   C. G. Kang and J. H. Yoon, “The Upsetting Behavior of Semi-Solid Aluminium Material Fabricated by a Mechanical Stirring Process”, Journal of Material Production Technology, Vol. 66, No. 1-3, 1997, pp. 30-38. doi:10.1016/S0924-0136(96)02493-4

[15]   XUY and Chung D.D.L, “Low Volume Fraction Particulate Performs for Making Metal-Matrix Composites by Liquid Metal Infiltration”, Journal of Material Science, Vol. 33, No. 19 1998, pp. 4707-4709. doi:10.1023/A:1004480819365

[16]   Y. H. Seo and C. G. Kang, “The Effect of Applied Pressure on Particle Dispersion Characteristics and Mechanical Properties in Melt-Stirring Squeeze-Cast SiCp/Al Composites,” Journal of Materials Production Technology, Vol. 55, No. 3-4, 1995, pp. 370-379.

[17]   J. C. Lee, J. Y. Byun, C. S. Oh, H. K. Seok and H. I. Lee, “Effect of Various Processing Methods on the Interfacial Reaction in SiCp/2024 Al Composites,” Acta Materials, Vol. 45, No. 12, 1998, pp. 5303-5315. doi:10.1016/S1359-6454(97)84851-3

[18]   J. Bar, H. K. Klubman and H. A. Gudladt, “Influence of Fiber Reinforcement on Microstructure of an Al-Si Based Alloy,” Scripta Materialia, Vol. 29, No. 6, 1993, pp 787-792.

[19]   S. Skolianos and T. Z. Kattamis, “Tribological Properties of SiCp-Reinforced Al4.5%Cu-1.5% Mg Alloy Composites,” Material Science Engineering: A, Vol. 163, No. 1, 1993, pp. 107-113. doi:10.1016/0921-5093(93)90584-2

[20]   A. Banerji, S. V. Prasad, M. K. Surappa and P. K. Rohatgi, “Abrasive Wear of Cast Aluminium Alloy-Zircon Particle Composites,” Wear, Vol. 82, No. 2, 1982, pp. 141-151. doi:10.1016/0043-1648(82)90288-5

[21]   M. K. Surappa, S. V. Prasad and P. K. Rohatgi, “Wear and Abrasion of Cast Al-Alumina Particle Composites,” Wear, Vol. 77, No. 3, 1982, pp. 295-302. doi:10.1016/0043-1648(82)90055-2

[22]   R. D. Pruthviraj, “Open Circuit Potential Studies of ZA-27/SiC Metal Matrix Composites in Acid Chloride Mediums,” Transactions of SAEST, Vol. 41, 2006, pp. 94-96.

[23]   J. Datta and C. Bhattacharya, “Bandyopadhyay,” Bulletin of Material Science, Vol. 28, No. 3, 2005, pp. 253-258. doi:10.1007/BF02711257

[24]   W.A. Badawy, F.M, Al-Kharafi and A.S. El-Azab, “Electrochemical Behaviour and Corrosion Inhibition of Al, Al-6061 and Al-Cu in Neutral Aqueous Solutions,” Corrosion Science, Vol. 41, No. 4, 1999, pp. 709-727. doi:10.1016/S0010-938X(98)00145-0

[25]   J. M. G. DeSalazar, A. Urefia, S. Mazanedo and M. Barrens, “Corrosion Behaviour of AA6061 and AA7075 Reinforced with Al2O3 Particulates in Aerated 3.5% Chloride Solution Potentiodynamic Measurements and Microstructure Evaluation,” Corrosion Science, Vol. 41, No. 3, 1999, pp. 529-545. doi:10.1016/S0010-938X(98)00135-8

[26]   J. E. Castle, L. Sun and H. Yan, “The Use of Scanning Auger Microscopy to Locate Cathodic Centers in SiC/Al6061 MMC and to Determine the Current Density at Which They Operate,” Corrosion Science, Vol. 36, No. 6, 1994, pp. 1093-1110. doi:10.1016/0010-938X(94)90206-2

[27]   B. M. Satish, et.al., “Corrosion Characteristics of ZA-27/ Glass-Fiber Composites,” Corrosion science, Vol. 39, No. 12, 1997, pp. 2143-2150. doi:10.1016/S0010-938X(97)00098-X

[28]   J. X. Wu, W. Liu P. X. Li and R. J. Wu, “Effect of Matrix Alloying Elements on the Corrosion Resistance of C/Al Composites Materials,” Journal of Materials Science Letters, Vol. 12, 1993, pp. 1500-1501.

[29]   A. Jameel, H. P. Nagaswarupa., P. V. Krupakara and K. C. Vijayamma, “Corrosion Characterization of Al6061/Zircon Metal Matrix Composites in Acid Chloride Mediums by Open Circuit Potential Studies,” International Journal of Applied Chemistry, Vol. 5, No. 1, 2009, pp. 1-10.

 
 
Top