MNSMS  Vol.3 No.1 , January 2013
Optimal Design of Thermal Dissipation for the Array Power LED by using the RSM with Genetic Algorithm
Abstract: In accordance with the enhancement for luminous efficiency improving, LED (Light Emitting Diode) has been gradually developed by combining the characteristics of small volume, impact resistance, good reliability, long life, low power consumption with multiple purposes for energy saving and environmental protection. Therefore, the array LED has been widely applied in human livings nowadays. This study applies the finite element analysis software ANSYS to analyze the thermal behavior of the array power LED work lamp which is modeled by four same-size LED with MCPCB (Metal Core Print Circuit Board) mounted on a base heat-sink. The Flotran heat flow analysis is applied to obtain the natural convection of air coefficient, while the convection value can be confirmed by the iterative method since it is set as the boundary condition for ANSYS thermal analysis to obtain the temperature distribution, accordingly the chip junction temperature and the base heat-sink temperature were followed through experiments in order to check if the simulation results meet the design requirements and coincide with the power LED product design specification. Prior to the optimal design process for chip junction temperature, the most significant parameters were first chosen by the fractional factorial design. The regressive models were respectively setup by the dual response surface method (RSM) and the mixed response surface method. Furthermore, the genetic algorithm combined with response surface method was applied to acquire the optimal design parameters, and the results were obtained from both methods, which are reviewed for comparison. Afterwards, the mixed response surface method is adopted to investigate the effects of interactions among various factors on chip junction temperature. In conclusion, it is found that the thermal conductivity of MCPCB and the height of base heat-sink are the two major significant factors. In addition, the interactive effects between chip size and thermal conductivity of chip adhesion layer are acknowledged as the most significant interaction influenced on the chip junction temperature.
Cite this paper: R. Chen, H. Cheng, C. Huang and R. Wu, "Optimal Design of Thermal Dissipation for the Array Power LED by using the RSM with Genetic Algorithm," Modeling and Numerical Simulation of Material Science, Vol. 3 No. 1, 2013, pp. 12-26. doi: 10.4236/mnsms.2013.31003.

[1], 2006.

[2]   J. Petroski, “Thermal Challenges Facing New Generation Light Emitting Diodes (LED) for Lighting Applications,” Procedings of SPIE Solid State Lighting II, Seattle, 26 November 2002, pp. 215-222. doi:10.1117/12.452579

[3]   H. Rainer, “Thermal management of Golden Dragon LED —Application Note,” Osram Opto Semiconductors, Regensburg, 2008.

[4]   J. Petroski, “Spacing of High-Brightness LEDs on Metal Substrate PCB’s for Proper Thermal Performance,” IEEE Intersociety Conference on Thermal Phenomena, Las Vegas, 1-4 June 2004, pp. 507-514. doi:10.1109/ITHERM.2004.1318326

[5]   M. Arik, C. Becker, S. Weaver, and J. Petroski, “Thermal Management of LEDs: Package to System,” Third International Conference on Solid State Lighting, San Diego, 26 January, 2004, pp. 64-75. doi:10.1117/12.512731

[6]   N. Narendran and Y. Gu, “Life of LED-Based White Light Source,” IEEE/OSA Journal of Display Technology, vol. 1, No.1, 2005, pp. 167-171. doi:10.1109/JDT.2005.852510

[7]   M. Arik and S. Weaver, “Effect of chip and bonding defects on the Junction Temperatures of High-Brightness Light-Emitting Diodes,” Optical Engineering, Vol. 44, No. 11, 2005, Article ID: 111305. doi:10.1117/1.2130127

[8]   C. Qian, “Thermal Management of High-Power White LED Package,” 8 International Conference on Electronic Packaging Technology, Harbin, 14-17 August 2007, pp.1-5. doi:10.1109/ICEPT.2007.4441417

[9]   L. Yang, J. Hu, L. Kim and M. W. Shin, “Thermal Analysis of GaN-Based Light Emitting Diodes With Different Chip Sizes,” IEEE Transactions on Device and Materials Reliability, Vol. 8, No. 3, pp. 571-575. doi:10.1109/TDMR.2008.2002357

[10]   J. P. You, Y. He and F. G. Shi, “Thermal Management of High Power LEDs: Impact of Die Attach Materials,” International Conference of Microsystems, Packaging, Assembly and Circuits Technology, Taipei, 1-3 October 2007, pp. 239-242. doi:10.1109/IMPACT.2007.4433607

[11]   P. Krivic, F.–P. Wenzl, C. Sommer, G. Langer, P. Pachler, H. Hoschopf, P. Fulmek, J. Nicolics, “Investigation of Thermal Properties of Power LED Illumination Assemblies,” 35 International Spring Seminar on Electronics Technology, Bad Aussee, 9-13 May 2012, pp. 76-83. doi:10.1109/ISSE.2012.6273112

[12]   Y. A. ?engel, “Heat Transfer: A Practical Approach,” McGraw-Hill, Inc., Boston, 2003.

[13]   Ralph Remsburg, “Thermal Design of Electronic Equipment,” CRC Press LLC, Boca Raton, 2001.

[14]   R. H. Myers, D. C. Montgomery and C. M. Anderson-Cook, “Response Surface Methodology,” 6th Edition, John Wiley & Sons, Inc., New York, 1995.

[15]   D. C. Montgomery, “Design and Analysis of Experiment,” 6th Edition, John Wiley & Sons, Inc., Singapore, 2005.

[16]   G. E. P. Box and J. S. Hunter, “The 2k?p Fractional Factorial Designs Part I,” Technometrics, Vol. 42, No. 1, 2000, pp.2 8-47. doi:10.2307/1271430

[17]   J. H. Holland, “Adaptation in Natural and Artificial System,” MIT Press, Cambridge, 1992.

[18]   J. K. Park, H. D. Shin, Y. S. Park, S. Y. Park, K. P. Hong and B. M. Kim, “A Suggestion for High Power LED Package Based on LTCC,” Proceedings of 56th Electronic Components and Technology Conference, San Diego, 30 May 2006, pp. 1070-1075. doi:10.1109/ECTC.2006.1645786