JMMCE  Vol.11 No.7 , July 2012
Effect of Surface Treatment on Tribological Behavior of Ti-6Al-4V Implant Alloy
ABSTRACT
Titanium alloys are extensively used in various fields of engineering, medicine, aerospace, marine due to its excellent mechanical properties. Its usage is more pronounced today in the field of biomedical implants due to its superior bio-compatibility, corrosive resistance and high strength to weight ratio. It has poor abrasive wear resistance due to high coefficient of friction and low thermal conductivity. Poor abrasive wear resistance results in the formation of wear debris at the implant area causing toxicity, inflammation and pain .Surface treatment of the implant alloy through heat treatment, application of protective coatings, introduction of compressive residual stresses by shotpeening and shot blasting are some of the methods to mitigate wear of the implant alloy. In this work Ti-6Al-4V implant alloy is treated under various conditions of heat treatment, shotpeening and shot blasting operations on a pin on disc wear testing machine. Shotpeening and Shot blasting are the operations usually performed on this alloy to improve fatigue strength and surface roughness. In this work the effect of above surface treatments were studied on the wear behavior of Ti-6Al-4V implant alloy and an improvement in the wear resistance of the alloy is reported. Scanning Electron micrograph (SEM) along with Energy Dispersive Spectrometry analysis (EDS) is done to authenticate the experimental results obtained during the wear testing procedure.

Cite this paper
B. Ganesh, N. Ramanaiah and P. Rao, "Effect of Surface Treatment on Tribological Behavior of Ti-6Al-4V Implant Alloy," Journal of Minerals and Materials Characterization and Engineering, Vol. 11 No. 7, 2012, pp. 735-743. doi: 10.4236/jmmce.2012.117061.
References
[1]   Xuanyong Liu, Paul .K. Chu, Chuanxian Ding (2004). “Surface modification of titanium, titanium alloys and related materials for biomedical applications, Journal of materials Science and Engineering (R), Volume 47,p-49-121

[2]   C.J.Boehlart, C.J.Cowen, J.P.Quast, T.Akahori, M.Niinomi (2008). “Fatigue and wear evaluation of Ti-Al-Nb alloys for biomedical applications”, Journal of Material Science & Engineering,(C), Volume 28 p 323-330.

[3]   Urs.I.Thomann, Petar. J Uggowitzer (2000). “Wear corrosion behavior of biocompatible austenitic stainless steel”, Journal of Wear, Volume 239, p 48-58.

[4]   Zhecheva. A, Sha. W, Malinov. S,Long.A, (2005), “Enhancing the microstructure and properties of titanium through nitriding and other surface engineering methods”, Surface Coatings and Technology, Volume 200, p2192-2207.

[5]   Mitsuo Niinomi.(2008). “Mechanical biocompatibilities of titanium alloys for biomedical applications”, Journal of Mechanical Behavior of Biomedical Materials, Volume 1, p 30-42.

[6]   Yongqing Fu,Nee lam Loh,Andrew W Batchelor (1998). “Improvement in fretting and fatigue resistance by application of several surface treatments and coatings”, Journal of Surface and Coatings Technology, Volume 106, p193-197.

[7]   A.Molinari, G Straffelini, B.Tesi, T.Bacci (1997). “Dry sliding wear mechanisms of the Ti6Al4V alloy”, Journal of Wear, Volume 208, p 105-112.

[8]   Md. Ohidul Alam, A.S.M.A.Haseeb. (2002). “Response of Ti-6Al-4V and Ti-24Al-11Nb alloys to dry sliding wear against hardened steel”, Journal of Tribology International, Volume 35, p 357-362.

[9]   S.J.Li, R.Yang. S.Li (2004). “Wear characteristics of Ti-nb-ta-zr and Ti-6al-4v alloys for biomedical applications “,Journal of Wear ,Volume 257,p 869-876

[10]   P.Majumdar,S.B.Singh,M.Chakraborty (2008). “Wear response of heat treated Ti-13 Zr-13Nb alloy in dry condition and simulated body fluid”, Journal of Wear, Volume 264 ,p 1015-1025.

[11]   M.P.Gispert, A.P.serro, R.Colaco, A.M.Botelho, Do Rego, “Tribological behavior of ci-implanted tin coatings for biomedical applications”, Journal of Wear, Volume 262, p 1337-1345.

[12]   Hasan Guleryuz, Huseyin Cimenglu, (2008),. Oxidation of Ti-6Al-4V alloy Article in Press, DOI : 10.1016/j.jallcom.2008.04.024.

[13]   A.K.Jha, S.K.Singh, M.S.Kiranmayee. (2010). “Failure analysis of titanium alloy (Ti-6Al-4V) fastener in aerospace application”, Journal of Engineering Failure Analysis, Volume 17, p 1457-1465.

[14]   Z.Mohammadi, A.A.Ziaei-Moayyed, A.Shekh-Mehdi Mesgar, (2007) “Grit blasting of Ti-6al-4v alloy: optimization and its effect on adhesion strength of plasma-sprayed hydroxyapatite coatings”, Journal of Materials processing Technology, Volume 194, p 15-23.

 
 
Top