JMMCE  Vol.10 No.15 , December 2011
Simulation of Torque during Rod Rolling of HC SS316 at Low Strain Rate Using “Phantom-Roll” Method
ABSTRACT
Rolling torque for a seventeen passes, 125 x 125 mm HC SS316 billets rolled to a 16 mm diameter rod have been simulated. Torque calculations based on pressure exerted by the metal on the rolls and the area of contact during longitudinal rolling were obtained using the temperature values derived using the “Phantom Roll” method. Investigations were carried out for four different starting mean rolling temperatures between 988℃ and 1191℃ and at four different strain rates of 0.4s-1, 0.8s-1, 1.2 s-1 and 1.6s-1. Results obtained showed that for all cases, rolling in grooved rolls required higher torque compared to rolling in flat rolls. In general, it was observed that torque value increased as starting temperature decreases and for each set of starting temperatures, the torque value increases with temperature. In all cases, the torque values for grooved rolls were higher than those for flat rolls. This was due to the higher frictional effect, occasioned by the larger contact area between roll and stock. Results obtained also revealed an inverse relationship between strain rate and torque.

Cite this paper
P. Aiyedun, O. Igbudu and B. Bolaji, "Simulation of Torque during Rod Rolling of HC SS316 at Low Strain Rate Using “Phantom-Roll” Method," Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 15, 2011, pp. 1473-1485. doi: 10.4236/jmmce.2011.1015114.
References
[1]   A.G. Antonio and R.V. Renato, The Effect of Finishing Temperature and Cooling Rate on the Microstructure and Mechanical Properties of As-Hot Rolled Dual Phase Steel, Antonio Augusto Gorni, 1996, Home page, http://www.Geocities.com.

[2]   P.J. Schaffer, A. Sexana, D.S. Antolovich, T.H. Sanders and B.S. Warner, Science and Design of Engineering Materials, 2nd ed., McGraw-Hill Company Inc., New York, 1999.

[3]   P.O. Aiyedun, O.S. Igbudu and B.O. Bolaji, Simulation of Load during Rod Rolling of HCSS316 at Low Strain Rate, Proceedings of 2nd International Conference on Engineering Research and Development: Innovation, April 15-17, 2008 (Nigeria), University of Benin, Benin City, Nigeria, 2008, p 422-430.

[4]   S. Venkadesan, P. Sivaprasad, S. Venugopal and V. Seetharaman, Tensile Deformation Behaviour of Warm-Rolled Type 316 Austenitic Stainless Steel, Journal of Mechanical Working Technology, 12, 1986, p 351-354.

[5]   E.C. Rollason, Metallurgy for Engineers 4th ed., Edward Anorld, New York, 1992.

[6]   H. Qamark, G.W. Buckley and M. Lewis, Computer Programmed Speed Roll-Torque Data Calculation, Journal of Iron and Steel International, 53, 1980, p 29-37.

[7]   R. Kawai, “Simulation of Rod Rolling of Carbon-Manganese Steel,” M.Phil. Thesis, University of Sheffield, UK, 1985.

[8]   L.E. Oseghale, “Simulation of Load and Torque During Rod Rolling Using the ‘Phanthom Roll’ Method,” M.Sc. Thesis, Univesity of Ibadan, Nigeria, 1998.

[9]   P.O. Aiyedun, “A study of loads and torque for light reduction in hot flat rolling at low strain rates,” Ph.D. Thesis, University of Sheffield, UK, 1984.

[10]   R.W.K. Honey-Combe, The Plastic Deformation of Metals, 2nd ed., Anorld, New York, 1983.

[11]   O.J. Alamu and M.O. Durowoju, Evaluation of Zener-Hollomon parameter variation with pass reduction in hot steel rolling, International Journal of Environmental Issues, 1, 2003, p 148-159.

[12]   P.O. Aiyedun, L.E. Oseghale and O.J. Alamu, Simulation of Load Bearing Rod Rolling of Carbon-Manganese Steel Using the “Phantom Roll” Method, Pacific Journal of Science and Technology, 10, 2009, p 4-14.

 
 
Top