JMMCE  Vol.10 No.15 , December 2011
Effects of Steel Fibers and Iron Filings on Thermal and Mechanical Properties of Concrete for Energy Storage Application
ABSTRACT
An experimental study on the thermal properties of iron filings and steel-fiber-reinforced concrete for solar/thermal energy storage application is presented in this report. It takes into account the results of measurements of thermal conductivity, thermal resistivity, thermal diffusivity and the results of compressive strength, density as well as energy storage capacity calculated from the knowledge of the above measured parameters. The experimental testing method is described as well: based upon the linear heat source theory, it requires the use of a special probe to be inserted into the sample. The experimentation was forwarded to test concrete aggregate mixtures with three different sizes and same quantity of steel fibers; two different quantities of iron filings and one plain concrete. The measurements were carried out from the pouring time of cubic samples and were ended up when hardened conditions were achieved. The results indicate that the steel fibers and iron filings have influence on the thermal and mechanical properties of the concretes tested, thus the iron filings and steel fibers reinforced concrete is suitable for better solar/thermal energy storage due to an increase in storage capacity over plain concrete.

Cite this paper
A. Adeyanju and K. Manohar, "Effects of Steel Fibers and Iron Filings on Thermal and Mechanical Properties of Concrete for Energy Storage Application," Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 15, 2011, pp. 1429-1448. doi: 10.4236/jmmce.2011.1015111.
References
[1]   Adeyanju, A.A and Manohar,K (2009) Theoretical and Experimental Investigation of Heat Transfer in Packed Beds. Research Journal of Applied Sciences.4 (5). Pp.166-167.

[2]   Rakshvir, M., and Barai, S.V. (2006). "Studies on Recycled Aggregates-Based Concrete." Waste Management & Research, 24, 225-233.

[3]   Neville, A.M., and Brooks, J.J. (1990). "Concrete Technology." Longman Group Limited, U.K.

[4]   Akinmusuru, J.O. (1991) "Potential Beneficial Uses of Steel Slag Wastes for Civil Engineering Purposes." Resources, Conservation and Recycling, 5, 73-80.

[5]   Ghailan, A.H. (2005). "Modified Concrete by Using a Waste Material as a Coarse Aggregate." Construction Research Congress: Broadening perspective-Proceedings of the Congress, 217-226.

[6]   Pezzi, L., De Lice, P., Vuono, D., Chiappetta, F., Nastro, A. (2006). "Concrete Products with Waste's Material (Bottle, Glass, Plate)." Materials Science Forum, 1753-1757.

[7]   Marzouk, O.Y., Dheilly, R.M., Queneudec. M. (2007). "Valorization of Post-Consumer Waste Plastic in Cementitious Concrete Composites." Waste Management, 27, 310-318.

[8]   Ismail, Z.Z., and Al-Hashmi, E.A. (2008). "Reuse of Waste Iron as a Partial Replacement of Sand in Concrete." Waste Management, 28, 2048-2053.

[9]   Kou, S.C., Lee, G., Poon, C.S, Lai, W.L. (2009). "Properties of Lightweight Aggregate Concrete Prepared With PVC Granules Derived from Scraped PVC Pipes." Waste Management, 29, 621-628.

[10]   ASTM C114. "Standard Chemical Analysis of Hydraulic Cement." Annual book of ASTM standards.

[11]   ASTM C204. "Standard Test Method for Fineness of Hydraulic Cement by Air Permeability Apparatus." Annual Book of ASTM Standards.

[12]   ASTM C191. "Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle." Annual book of ASTM standards.

[13]   ASTM C151. "Standard Test Method for Autoclave Expansion of Hydraulic Cement." Annual book of ASTM standards.

[14]   ASTM C109. "Standard Test Method for Compressive Strength of Hydraulic Cement." Annual Book of ASTM Standards.

[15]   Somayaji, S. (1995). "Civil Engineering Materials." Prentice-Hall, Inc., Englewood Cliffs, New Jersey.

[16]   ASTM C293. "Standard Test Method for Flexural Strength of Concrete Using Simple Beam With Center-Point Loading." Annual book of ASTM standards.

[17]   Decagon Devices Incorporated (2001). KD2 Thermal Properties Analyzer User's Manual, Version 1.0. http://www.thermalresistivity.com/KD2man.pdf (2006/01/23).

[18]   Johnston, C.D. (1974) “Steel fiber reinforced mortar and concrete”, A review of mechanical properties. In fiber reinforced concrete ACI – SP 44 – Detroit 1974.

[19]   ASTM C1018. "Standard Test Method for Flexural Toughness and First Crack Strength of Fiber-Reinforced Concrete (Using Beam with Third-Point Loading)." Annual Book of ASTM Standards.

[20]   Johnston, C.D. (1982) “Definition and measurement of flexural toughness parameters for fiber reinforced concrete” Cement Concrete Aggregate 1982.

 
 
Top