JMMCE  Vol.10 No.12 , October 2011
Taguchi Technique for the Simultaneous Optimization of Tribological Parameters in Metal Matrix Composite
ABSTRACT
Taguchi methods have proved to be successful over the last two decades for improvement of product quality and process performance. This study is carried out to simultaneously optimize the tribological properties: wear rate and frictional force of aluminum metal matrix composite. Al-Cu-Mg alloy reinforced with 6 Wt % of titanium dioxide was prepared using stir casting method. Dry sliding wear test was conducted to understand the tribological behavior of samples. The experiments were conducted as per the Taguchi design of experiment. The wear parameters chosen for the experiment were: sliding speed and load and sliding distance. Each parameter was assigned three levels. The experiment consists of 27 tests according to L27 orthogonal array. Signal to noise ratio analysis has been carried out to determine optimal parametric condition, which yields minimum wear rate and frictional force. Harrington’s desirability functional method is adopted for multifunctional optimization of tribological parameters and the confirmation experiments were conducted to verify the predicted model.

Cite this paper
K. Hemanth, R. Swamy and T. Chandrashekar, "Taguchi Technique for the Simultaneous Optimization of Tribological Parameters in Metal Matrix Composite," Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 12, 2011, pp. 179-188. doi: 10.4236/jmmce.2011.1012090.
References
[1]   Mingzhao Tan, Qibin Xin, Zhenghua Li, B. Zong, Y. Influence of SiC and Al2 O3 particulate reinforcements and heat treatments on mechanical properties and damage evolution of Al-2618 metal matrix composites. Journal of Materials science 36 (2001) 2045 -2053.

[2]   Nitsham. .A. E. New application for Aluminum based metal matrix composites. 1997. Vol. 54. Light metal age. USA.

[3]   Debdas Roy. Bikramjit Basu. Amitava Basu Mallick. Tribological properties of Tialuminide reinforced Al-based In- Situ –metal matrix composite. Intermetallics 13 (2005) 733 – 740.

[4]   A. P. Sannino, H.J. Rack.. Dry sliding wear of discontinuously reinforced aluminum composites: review and discussion. Wear 189 (1995) 1-19.

[5]   R.N. Rao. S.Das and P.V. Krishna. Experimental investigation on the influence of SiC particulate reinforcement in Al alloy composites.

[6]   Prasanna Kumar.M. Sadashivappa.K. Prabhukumar.G.P. and Basavarajappa.S. Dry sliding wear behavior of Garnet reinforced metal matrix composite. Materials science. Vol.12. No.3. 2006. PP. 209 -213.

[7]   G.Ranganath. S.C. Sharma and M. Krishna. Dry sliding wear of Garnet reinforced Zink / Al MMCs. Wear. 251 (2001) 1408 – 1413.

[8]   S.C. Sharma. M.Krishna. P.V.Vizhian and A.Shashishankar. Thermal effects on Mild wear behavior of al 7075-glass fiber reinforced composite. Vol.216. No.12/2002. PP. 975-982.

[9]   Ramachandra M, Radhakrisna. Sliding wear, slurry erosive wear and corrosive wear of Al /SiC composites.Material science. Vol. 24. No. 2/1.2006.

[10]   G.Ranganath. S.C. Sharma and M. Krishna. Dry sliding wear of Garnet reinforced Zink / Al MMCs. Wear. 251 (2001) 1408 – 1413

[11]   Wilson S, alpas. A.T. Wear mechanism map for metal matrix composites. Wear. 1997; 212: 41-49.

[12]   S. Basavarajappa. G. Chandramohan. R. Subramanian. Chandrasekar. Dry sliding wear behavior of Al 2219 / SiC metal matrix composites. Materials science Poland. Vol. 24. No. 2 /1. 2006.

[13]   R.L. Deuis. C. Subrananian and J. M. Yellup. Abrasive wear of Aluminum composites. A review. Wear. 201. (1996) 132 – 144.

[14]   R.K. Uyyuru, M.K. Surappa. S. Brusethaug. Effect of reinforcement Vol fraction and size distribution on the tribological behavior of Al - composite. Wear. 260 (2006) 1248 – 1255.

[15]   A Martin, J Rodriguez, J. Lorea. Temperature effects on the wear behavior of particulate reinforced Al-based composites. Wear. 255-229 (1999) 615-620.

[16]   J.M Gomez de, Salazar, M.I. Barrena. Influence of heat treatments on the wear behavior of an AA 6092 / SiC composites. Wear. 256 (2004) 286 -293.

[17]   J Guo, X Yuan. The aging behavior of SiC /Gr/6013 Al composites in T-4 –T-6 treatments.

[18]   Grigoris E. Kiourtsidis, stefanos M. Skolianos. Wear behavior of artificially aged AA2024 /SiC composites in comparison with conventionally wear resistance ferrous materials. Wear. 253 (2002) 946 -956.

[19]   Phillip. J. Ross. Taguchi techniques for quality engineering. Mc. Graw hill, New York. 1-179. (2005)

[20]   J.H. Hatch (ed), Aluminum: properties and physical metallurgy, ASM, Metals park, OH, (1988), 371.

[21]   James C. Williams. Progress in structural materials for Aerospace systems. Acta materials. 51 (2003) 5775 – 5799.

[22]   Gaitonde v.n, Achyutha.B.T, Siddeshwarappa.B. Burr size minimization in drilling using taguchi technique. Indian Journal of engineering & Materials. Vol. 12. April 2005. PP. 91-96.

[23]   Derringer G & Suich R. Simultaneous optimization of several response variables. Journal of quality technology. 12 (1980) 214 -219.

 
 
Top