JMMCE  Vol.10 No.12 , October 2011
Development and Calibration of a Quantitative, Automated Mineralogical Assessment Method Based on SEM-EDS and Image Analysis: Application for Fine Tailings
ABSTRACT
Quantitative mineralogy has seen significant developments from the combination of scanning electron microscopy (SEM) with automatic image analysis and energy dispersive X-ray spectrometry (EDS). The mining industry is one of the fields that has benefited from this progress. In this paper, the authors present a newly developed quantitative method based on SEM-EDS and image analysis (IA), which is used to determine the mineralogical and environmental characteristics of mine tailings. The main objectives of the method are to be able to characterize sulphides and carbonates as monomineral particles, which control the acid generation from the tailings. Pure sulphides, calcite and quartz were blended to make mineralogical standards that represent typical mine tailings environmental behavior. The SEM-EDS-IA method achieved good mineralogical precision for medium (1-20 Wt%) and abundant (> 20 Wt%) minerals, with a relative error below 10 %. However, some corrections had to be applied to account for typical stereological effects (apparent particle diameter from polished surface) and preparation modes (particle segregation during resin hardening). Particle size analysis was used to calibrate the method and identify the corrections to be applied. Since mineralogical quantifications are based on the area of the observed particles, the most reliable particle size analyses (also obtained from particle area) typically lead to the best mineralogical characterization. However, the SEM based techniques may show some limitations for fine-grained particle quantification (< 10 μm), which required additional corrections. In this article, the technique is described, and it is applied to characterize fine-grained mine tailings with a size-by-size mineralogy (with sulphides and carbonates content). These results have been used by the Authors to propose an environmental management strategy for acid generating tailings using desulphurization by flotation.

Cite this paper
R. Mermillod-Blondin, M. Benzaazoua, M. Kongolo, P. Donato, B. Bussière and P. Marion, "Development and Calibration of a Quantitative, Automated Mineralogical Assessment Method Based on SEM-EDS and Image Analysis: Application for Fine Tailings," Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 12, 2011, pp. 1111-1130. doi: 10.4236/jmmce.2011.1012085.
References
[1]   Kwong, Y.T.J., 1993, Prediction and prevention of acid rock drainage from a geological and mineralogical perspective. MEND Report 1.32.1, Ottawa, CANMET.

[2]   Lapakko, K.A. 1994, Evaluation of neutralisation potential determinations for metal mine waste and a proposed alternative, in: The International Land Reclamation and Mine Drainage Conference and the Third International Conference on the Abatement of Acidic Drainage, Pittsburgh.

[3]   Paktunc, A.D., 1999, “Mineralogical constraints on the determination of neutralization potential and prediction of acid mine drainage.” Environmental Geology, Vol. 39, No. 2, pp. 103-112.

[4]   Bouzahzah, H., Califice, A., Benzaazoua, M., Mermillod-Blondin, R., and Pirard, E., 2008, Modal analysis of mineralogical blends using optical image analysis versus XRay diffraction, in: Proceeding of the International Congress of Applied Mineralogy, Brisbane.

[5]   Paktunc, A.D., 1999, Characterization of Mine Wastes for Prediction of Acid Mine Drainage, in: Environmental Impacts of Mining Activities, pp. 31-36 (Azcue, J.M., Ed.), Berlin, Springer.

[6]   Sutherland, D.N., and Gottlieb, P., 1991, Application of automated quantitative mineralogy in mineral processing, Minerals Engineering, Vol. 4, No. 7-11, pp. 753- 762.

[7]   Sutherland, D., 2007, “Estimation of grain size using automated mineralogy.” Minerals Engineering, Vol. 20, No. 5, pp. 452-460.

[8]   Knight, R.D., Klassen, R.A. and Hunt, P., 2002, “Mineralogy of fine-grained sediment by energy dispersive spectrometry (EDS) image analysis - a methodology.” Environmental Geology, Vol. 42, pp. 32-40.

[9]   Kahn, H., Mano, E. S., and Tassinari, M. M. M. L., 2002, “Image analysis coupled with a SEM-EDS applied to the characterization of a partially weathered Zn-Pb ore.” J. of Minerals & Materials Characterization & Engineering, Vol. 1, No. 1, pp. 1-9.

[10]   Gu, Y., 2003, “Automated scanning electron microscope based mineral liberation analysis. An introduction to JKMRC/FEI Mineral Liberation Analyser.” J. of Minerals & Materials Characterization & Engineering, Vol. 2, No. 1, pp. 33-41.

[11]   Petruk, W., 1976, “The application of quantitative mineralogical analysis of ores to ores dressing.” CIM Bulletin, Vol. 767, pp. 146-153.

[12]   Lastra, R., Petruk, W., and Wilson, J.M.D., 1998, Image-analysis techniques and applications to mineral processing, in: Commission on Ore Mineralogy, International Mineralogical Association, Volume 27, pp. 327-366, (Cabri, L.J., and Vaughan, D.J., Eds.), Ottawa, Mineralogical Association of Canada.

[13]   Wilson, J.M.D., and Lastra, R., 1999, Quantification of silicate minerals by SEM-based image analysis, in: TMS Symposium, San Diego, The Minerals, Metals & Materials Society.

[14]   Petruk, W., and Lastra, R., 1997, Measuring mineral liberation and mineral associations from polished sections by image analysis, in: Proceedings XX IMPC, Volume 2, pp. 111-119, Aachen.

[15]   Lin, D., Lastra, R., and Finch, J.A., 1999, Comparison of stereological correction procedures for liberation measurements by use of a standard material, in: Trans. Instn Min. Metall. (Sect. C: Mineral Process. Extr. Metall.), Volume 108, pp. C127-C137.

[16]   Petruk, W., 2000, Applied Mineralogy in the Mining Industry, Elsevier, Amsterdam.

[17]   JKTech, 2007, http://www.jktech.com.au/Products_Services/MLA/

[18]   Zhou, J., 2010, Process mineralogy of silver ores and application in flowsheet design and plant optimization, in: Proceeding of the 42nd Annual Canadian Mineral Processors Conference, pp. 143-162, Ottawa, the Canadian Institute of Mining, Metallurgy and Petroleum.

[19]   Intellection, 2007, http://www.intellection.com.au/auto_analysis.html.

[20]   Lotter, N.O., Whittaker, P.J., Kormos, L., Stickling, J.S., and Wilkie, G.J., 2002, “The development of process mineralogy at Falconbridge Limited and application to the Raglan Mill”. CIM Bulletin, Vol. 95, No. 1066, pp. 85-92.

[21]   Pascoe, R.D., Power, M.R., and Simpson, B., 2007, “QEMSCAN analysis as a tool for improved understanding of gravity separator performance.” Minerals Engineering, Vol. 20, No. 5, pp. 87-95.

[22]   Kormos, L., Oliviera, J., Fragomeni, D., Whitman, E., and Carrión De la Cruz, J., 2010, Process diagnosis using quantitative mineralogy, in: Proceeding of the 42nd Annual Canadian Mineral Processors Conference, pp. 143-162, Ottawa, the Canadian Institute of Mining, Metallurgy and Petroleum.

[23]   Mermillod-Blondin, R., Benzaazoua, M., Kongolo, M., de Donato, P., and Aubertin, M., 2003, Quantitative mineralogy using image analysis on scanning electron microscopy: environmental application for mill tailings, in: Proceedings Applied Mineralogy 03, (Wills, B., Ed.), Helsinki, Minerals Engineering Conference.

[24]   Kelly, R.N., DiSante, K.J., Stranzl, E., Kazanjian, J.A., Bowen, P., Matsuyama, T., and Gabas, N., 2006, “Graphical comparison of image analysis and laser diffraction particle size analysis data obtained from the measurements of nonspherical particle systems.” AAPS Pharma. Sci. Tech., Vol. 7, No. 3, pp. E1-E14.

[25]   Barthelmy, D., 2005, http://www.webmineral.com.

[26]   Petruk, W., 1978, Correlation between grain sizes in polished section with sieve data and investigation of mineral liberation measurements from polished sections. Transactions/ Section C of the Institution of Mining and Metallurgy, Vol. 87, pp. c271-c278.

[27]   Miles, R.E., 1974, On the elimination of the edge-effects in planar sampling, in: Stochastic geometry: a tribute to the memory of Rollo Davidson, pp. 228-247 (Harding, E.F., and Kendall, D.G., Eds.), London, New York, Sydney, and Toronto, John Wiley and Sons.

[28]   Lantuéjoul, C., 1978, Computation of the histograms of the number of edges and neighbours of cells in a tessellation, in: Proceeding Geometrical Probability and Biological Structures: Buffon’s 200th Anniversary, Volume 23, pp. 323-329, (Miles, R.E. and Serra, J., Eds.), Lectures notes in Biomathematics, Berlin, Springer.

[29]   Exner, H.E. and Giess, E.A., 1989, A stereology-based equation for isotropic shrinkage during sintering by viscous flow, Science of Sintering Seventh, Plenum, New York.

[30]   King, M.P. and Schneider, 1995. Basic image analysis for the measurement of mineral liberation, in: Proceedings Process Mineralogy XIII: Applications to Beneficiation Problems, Pyrometallurgical Products, Advanced Mineralogical Techniques, Precious Metals, Environmental Concerns, Ceramic Materials, Hydrometallurgy, and Minerals Exploration. (Hagni, R.D., Ed), The Mineral, Metals & Materials Society.

[31]   Wehr, S.D., and Shaw, J.M., 2002, “A note on the misuse of area images to obtain particle size information in solid-solid systems.” Canadian Metallurgical Quarterly, Vol. 41, No. 3, pp. 365-372.

[32]   Jones, M.P., 1987, Applied Mineralogy. A quantitative approach, Graham & Trotman, London.

[33]   Rosin, P., and Rammler E., 1933, “The law governing the fineness of powdered coal.” Journal Inst. Fuel, Vol. 7, pp. 29-36, and discussion, pp. 109-122.

[34]   Kelly, E.G., and Spottiswood, D.J., 1982, Introduction to Mineral Processing, Wiley- Interscience, New York.

[35]   Mermillod-Blondin, R., 2006, Influence of the pyrite surface properties on the collection of sulphurous organic molecules: Application to the desulphurization of mine tailings, Ph.D. Thesis, INPL-ENSG-LEM and école Polytechnique de Montréal, Nancy, France and Montreal, Quebec (in French).

[36]   Benzaazoua, M., Bussière, B., Kongolo, M., McLaughlin, J., and Marion, P., 2000. “Environmental desulphurization of four Canadian mine tailings using froth flotation.” Int. J. of Mineral Processing, Vol. 60, pp. 57-74.

 
 
Top