JMMCE  Vol.10 No.4 , March 2011
Influence of Material Condition on the Dry Sliding Wear Behavior of Spring Steels
Author(s) K. V. Arun*, K.V. Swetha
ABSTRACT
During the past two decades, considerable efforts have been made in the development of high performance spring steels to meet the needs for weight and savings in the automotive industry. During the service the suspension system will be subjected to different environmental conditions, at the same time it has to sustain a variety of loads acting on it. Among all the wear of spring steel plays a vital role. In this experimental analysis an attempt has been made to investigate the performance of spring steel (EN-47 / SUP 10) under the dry sliding condition. The specimen preparation and the experimentations have been carried out according to the ASTM G99 standards. The effects of tempering and cryogenic treatments on the performance of the spring steel have also been determined. The results have revealed that the material condition has got a significant influence on the performance of the spring steel. In order to analyze the percentage contribution of different wear parameter and the material condition, the DOE and ANOVA have been made. The results have shown that the load (49.205%) has shown the highest influence and the material condition has shown 22.56% of contribution on wear behavior.

Cite this paper
K. Arun and K. Swetha, "Influence of Material Condition on the Dry Sliding Wear Behavior of Spring Steels," Journal of Minerals and Materials Characterization and Engineering, Vol. 10 No. 4, 2011, pp. 323-337. doi: 10.4236/jmmce.2011.104023.
References
[1]   J.P. Wise, J. Spice, S.G. Davidson, W.E. Heitmann and G. Krauss, “Influence of short austenizing times on the fracture behavior of a micro alloyed automotive spring steel” , scripta mater, Vol 44, Year 2001, Pp 299-304.

[2]   C.S. Lee, K.A. Lee, D.M. Li, S.J. Yoo , W.J. Nam, “Microstructural influence on fatigue properties of a high-strength spring steel” ,material science and engineering , Vol A241, Year 1998, Pp 30-37.

[3]   Sinan Fank Tubitak, Ulusal Metroloji Enstitusu, Gebze, Kocaeli, “Different heat treatment processes can be applied on the spring element of a force transducer in order to obtain good and satisfactory performance”.

[4]   A. Ardehali Barani, D. Ponge, D. Raabe, “Refinement of grain boundary carbides in a Si–Cr spring steel by thermo mechanical treatment”, Materials Science and Engineering, Vol A 426, Year2006, Pp 194–201.

[5]   D. Das, A.K. Dutta, K.K. Ray, “Influence of varied cryotreatment on the wear behavior of AISI D2 steel”, wear, Vol 266, Year 2009, Pp 297-309.

[6]   Paolo Baldissera, Cristiana Delprete, “Effects of deep cryogenic treatment on static mechanical properties of 18NiCrMo5 carburized steel”, Materials & Design, Volume 30, Issue 5, May 2009, Pages 1435-1440.

[7]   R. Jones, L. Molent, S. Pitt, “Crack growth of physically small cracks”, Engineering, Monash International Journal of Fatigue, Vol 29, Year 2007, Pp 1658–1667

[8]   B. Ravi Kumar, D.K. Bhattacharya, Swapan K. Das, Sandip Ghosh Chowdhury, “Premature fatigue failure of a spring due to quench cracks” ,engineering failure analysis , Vol 7, Year 2000 ,Pp 377-384.

[9]   Won Jong Nam, Chong Soo Lee , Deok Young Ban , “Effects of alloy additions and tempering temperature on the sag resistance of Si–Cr spring steels”, Materials Science and Engineering, Vol A289, Year2000, Pp 8–17.

[10]   M. Molnarova, I. mamuzi , J. Bacso, , M. Fujda, P. Kodronova, T. Kuskuli, I. Pokorny, “Influence of reheating and cooling conditions on structure and mechanical properties of c-mn-si steel”, Metalurgija, Vol 47 , Year 2008, Pp 187-190.

[11]   Masami Wakita and Takanori Kuno and Ayamitsu Amano, Akihiko Nemoto and Katsushi Saruki and Keisuke Tanaka ,“Study on Predicting Formula for Torsional Fatigue Strength of Spring Steel- Effect of Environment, Notch and Hardness”

[12]   Y. Sahin, “Optimal testing parameters on the wear behavior of various steels”, Materials and design, Vol 27, Year 2006, Pp 455-460.

[13]   Yoshifumi Amamoto, Hozumi Goto “Friction and wear of carbon steel near T1-transition under dry sliding”, Tribology International, Vol39, Year 2006, Pp 756–762.

[14]   Y. Totik, R. Sadeler, H. Altun, M. Gavgali, “The effects of induction hardening on wear properties of AISI 4140 steel in dry sliding conditions”, Materials & Design, Volume 24, Issue 1, February 2003, Pages 25-30.

[15]   Mare Meyers and Krishan chawla, “Mechanical behavior of materials (Second edition)”

[16]   S. Basavarajappa, K.V. Arun, J. Paulo Davim, “Effect of Filler Materials on Dry Sliding Wear Behavior of Polymer Matrix Composites – A Taguchi Approach”, Journal of Minerals & Materials Characterization & Engineering, Vol. 8, No.5, Pp 379-391, 2009

[17]   Ross, P.J. Taguchi Techniques for Quality Engineering, McGraw–Hill Publishing Company Ltd.: New York, 1988.

[18]   N.E.W. Hartley, J.K. Hirvonen ,”Wear testing under high load conditions, The effect of “anti-scuff” additions to AISI 3135, 52100 and 9310 steels introduced by ion implantation and ion beam mixing”, Nuclear Instruments and Methods, Vol 209/210, Year 1983, Pp 933-940.

 
 
Top