JMMCE  Vol.8 No.8 , August 2009
Model for Predicting the Quantity of Water Evaporated during Initial Stage Drying of Wet Clay Designated for Production of Bricks
Author(s) C. I. Nwoye*
ABSTRACT
Model for predicting the quantity of water evaporated during drying of clay at a temperature range 80-110℃ has been derived. The model; E=exp[0.3424(LogT)2.3529] indicates that the quantity of evaporated water during the drying process is dependent on the drying temperature, the evaporating surface being constant. The validity of the model is rooted in the expression (lnE x Log β)N = Log T since both sides of the expression are correspondingly approximately equal to 2. The respective deviation of the model-predicted quantity of evaporated water from the corresponding experimental value is less than 20% which is quite within the acceptable deviation range of experimental results, hence depicting the usefulness of the model. Water evaporation per unit rise in the drying temperature evaluated from experimental and model-predicted results are 0.078 and 0.0502g/℃ respectively, indicating proximate agreement.

Cite this paper
C. Nwoye, "Model for Predicting the Quantity of Water Evaporated during Initial Stage Drying of Wet Clay Designated for Production of Bricks," Journal of Minerals and Materials Characterization and Engineering, Vol. 8 No. 8, 2009, pp. 647-658. doi: 10.4236/jmmce.2009.88056.
References
[1]   Barsoum, M. (1997) Fundamentals of Ceramics. McGraw Hill Incorporated, Singapore p410

[2]   Unal, A. (1986) Trans Institute of Metallurgy Section C. 95, p179.

[3]   Furnass, C.C. (1928) The Relationship Between Specific Voids and Size of Compression In System of Broken Solid of Mixed Size US Bureau Report Investigation Vol. 2894 p 321-340.

[4]   Singer, F., Singer, S.S. (1963) Industrial Ceramics, University Press Cambridge p44.

[5]   Nwoye, C. I. (2003) Investigating the Influence of Particle Size and Size Distribution on the Physical and Mechanical Properties of Ceramic Materials. A Project Report p5-8, 16-22.

[6]   Viewey, F., Larrly, P. (1978) Ceramic Processing Before Firing, John-Wiley and Sons, New York, p3-8.

[7]   Arisa, U. S. (1997) Effect of Initial Particle Size and Size Distribution on Physical and Mechanical Properties of Some Nigeria Clays Sintered at 1200℃. A Thesis Report, p3,15-18

[8]   Nwoye, C. I. (2009) Studies on Pore Deformation Mechanism in Particles J. Eng. Appl. Sc.(in press)

[9]   Nwoye, C. I. (2008) Effect of Porosity on the Shrinkage Behaviour of Ukpor and Nsu Clays. J. Eng. Appl. Sc., 3(1, 2): 27-30.

[10]   Reed, J. (1988) Principles of Ceramic Processing, Wiley Interscience Publication, Canada p470-478.

[11]   Keey, R.B., (1978) Introduction to Industrial Drying Operations, Pergamon Press, Elmsford, New York. p132-157.

[12]   Nwoye, C. I. (2008) Mathematical Model for Computational Analysis of Volume Shrinkage Resulting from Initial Air-Drying of Wet Clay Products. Int. Res. J. Eng. Sc. & Tech. 5(1):82-85.

[13]   Nwoye, C. I., Iheanacho, I. O., Onyemaobi, O. O. (2008) Model for the Evaluation of Overall Volume Shrinkage in Molded Clay Products from Initial Air-Drying Stage to Completion of Firing. Int. J. Nat. Appl. Sc. 4(2): 234-238.

[14]   Nwoye, C. I. (2009) Model for Calculating the Quantity of Water Lost by Evaporation during Oven Drying of Clay. Researcher, 1(3): 8-13.

[15]   Nwoye, C. I., Okeke, K., Obi, M., Nwanyanwu, U., Ofoegbu, S. (2009) Model for Predictive Analysis of the Quantity of Water Evaporated during the Primary-Stage Processing of Bioceramic Material Sourced from Kaolin. J. Nat. Sc. 7(4): 79-84.

[16]   Nwoye, C. I., Nwakwuo, C. C., Obi, M. C., Obasi, G. C., Onyemaobi, O. O. (2009) Model for Quantifying the Extent and Magnitude of Water Evaporated during Time Dependent Drying of Clay. New York J. Sc. 2(3): 55-58.

[17]   Nwoye, C. I. (2007). SynchroWell Research Work Report, DFM Unit, No 20072002, p67-80.

 
 
Top