JMMCE  Vol.8 No.5 , May 2009
Effect of Filler Materials on Dry Sliding Wear Behavior of Polymer Matrix Composites – A Taguchi Approach
ABSTRACT
The tribological behaviour of glass epoxy polymer composites with SiC and Graphite particles as secondary fillers was studied using a pin-on-disc wear rig under dry sliding conditions. The influence of wear parameters like, applied load, sliding speed, sliding distance and percentage of secondary fillers, on the wear rate were investigated. A plan of experiments, based on the techniques of Taguchi, was performed to acquire data in a controlled way. An orthogonal array and analysis of variance (ANOVA) were employed to investigate the influence of process parameters on the wear of these composites. The results showed that the inclusion of SiC and Graphite as filler materials in glass epoxy composites will increase the wear resistance of the composite greatly.

Cite this paper
S. Basavarajappa, K. Arun and J. Davim, "Effect of Filler Materials on Dry Sliding Wear Behavior of Polymer Matrix Composites – A Taguchi Approach," Journal of Minerals and Materials Characterization and Engineering, Vol. 8 No. 5, 2009, pp. 379-391. doi: 10.4236/jmmce.2009.85034.
References
[1]   Sampathkumaran, K. P., Seetharamu, S., Vynatheya, S., Murali, S., Kumar, R.K., 2000,“SEM observations of the effects of velocity and load on the sliding wear characteristics of glass fabric–epoxy composites with different fillers.” Wear, Vol. 237, pp. 20–27.

[2]   Collyer, A.A., 1994, Rubber Toughened Engineering Materials, Chapman & Hall, London.

[3]   Pihtili, H., Tosun, N., 2002, “Investigation of the wear behaviour of a glass fibre-reinforced composite and plain polyester resin.” Composite Sci. Technol., Vol. 62, pp. 367–370.

[4]   El-Tayep, N.S., Gadelrap, R.M., 1996, “Friction and wear properties of E-glass fiber reinforced epoksi composites under different sliding contact conditions.” Wear, Vol. 192, pp.112–117.

[5]   Chand, N., Naik, A., Neogi, S., 2000, “Three-body abrasive wear of short glass fibre polyester composite.” Wear, Vol. 242, pp. 38–46.

[6]   Piggot, M. R., 1980, Load-Bearing Fibre Composite, Pergamon Press, Oxford.

[7]   Kukureka, S.N., Hooke, C. J., Rao, M., Liao, P., Chen, Y. K., 1999, “The effect of fibrereinforcement on the friction and wear af polyamide 66 under dry rolling–sliding contact.” Tribol. Int., Vol. 32, pp. 107–116.

[8]   Zum Gahr, K.H., 1987, Microstructure and wear of materials, Tribology Series, Vol. 10, Elsevier, Amsterdam.

[9]   Friedrich, K., 1986, Friction and Wear of Polymer Composites, Composite Materials Series, Elsevier, Amsterdam, Vol. 1, pp. 233–287.

[10]   Xue, Q., Wang, Q., 1997 “Wear mechanisms of polyetheretherketone composites filled with various kinds of SiC.” Wear, Vol. 213, pp. 54-58.

[11]   Suresha, and Chandramohan, G., (Article in press), “Friction and Wear Characteristics of Carbon-epoxy and Glass-epoxy oven Roving Fiber Composites.” J.Reinforced Plastics and Composite.

[12]   Chandramohan, B. G., and Davim, J. P., “Application of Taguchi techniques to study the dry sliding wear behavior of metal matrix composites”. accepted 3 January 2006.

[13]   Taguchi, G., and Konishi, S., 1987 “Taguchi methods, orthogonal arrays and linear graphs, in tools for quality engineering.” American supplier institute, pp 35-38.

[14]   Taguchi, G., 1993, “Taguthi on robust technology development methods”, ASME press, New York, pp 1-40.

[15]   Ross, P. J., 1993, Taguchi technique for quality engineering, Mc Graw-Hill, New York, pp.1-40.

[16]   Roy, K. R., 1990, A primer on Taguchi method, Van Nostrad reinhold, New York.

[17]   Basavarajappa, S., Chandrmohan, G., Mahadevan, A., Mukundan, Subramanian, R., Gopalakrishan, P., 2007, “Influence of sliding speed on the dry sliding wear behavior and the subsurface deformation of hybrid metal matrix composite.” Wear, Vol. 262, pp. 1007-1012.

[18]   Suresha, B. , Chandramohan, G. , Prakash, J. N., Balusamy, V., Sankaranarayanasamy K., 2006, “The Role of Fillers on Friction and Slide Wear Characteristics in Glass-Epoxy Composite Systems.” Journal of Minerals & Materials Characterization & Engineering, Vol. 5, pp 87-101.

 
 
Top