JMMCE  Vol.5 No.1 , June 2006
The Role of Fillers on Friction and Slide Wear Characteristics in Glass-Epoxy Composite Systems
ABSTRACT
The comparative performance of Glass-Epoxy (G-E) composite systems interfaced with graded fillers has been examined. In this study, composite materials were experimentally investigated under varying load and sliding velocities by using a Pin-on-Disc type wear tester. The influence of two inorganic fillers, silicon carbide particles (SiC) and graphite, on the wear of the glass fabric reinforced epoxy composites under dry sliding conditions has been investigated. For increased load and sliding velocity situations, higher wear loss was recorded. Some of these observations are supplemented by scanning electron microscopic (SEM) investigations. The coefficients of frictional values show an increasing trend with subsequent increase in load/sliding velocities. It was observed that the Graphite filled G-E composite shows lower coefficient of friction than the other two composites irrespective of variation in the load/sliding velocities. SiC filled G-E composite exhibited the maximum wear resistance. Further, wear of the matrix, breakage of reinforcing fibers, matrix debris formation and interface separation were observed in unfilled and graphite-filled G-E composites. Other interesting SEM features have been noticed and discussed.

Cite this paper
B. Suresha, G. Chandramohan, J. Prakash, V. Balusamy and K. Sankaranarayanasamy, "The Role of Fillers on Friction and Slide Wear Characteristics in Glass-Epoxy Composite Systems," Journal of Minerals and Materials Characterization and Engineering, Vol. 5 No. 1, 2006, pp. 87-101. doi: 10.4236/jmmce.2006.51006.
References
[1]   ASM Hand book, 1992, Materials Park, Ohio, USA, ASM International, Volume 18.

[2]   Pascoe, M.W., 1973, “Plain and filled plastics materials in bearing: a review.” Tribology, Vol. 6 No. 5, pp. 184-190.

[3]   Sung, N.H., and Suh, N.P., 1979, “Effect of Fiber orientation on friction and wear of fiber reinforced polymeric composites.” Wear, Vol. 53, pp. 129-141.

[4]   Chang, H.W., 1983, “Wear characteristics of composite: effect of fiber orientation.” Wear, Vol. 85, No. 1, pp. 81-91.

[5]   Suresha, B., Chandramohan, G., Samapthkumaran, P., Seetharamu, S., and Vynatheya, S., 2006, “Friction and wear characteristics of carbon-epoxy and glassepoxy woven roving fiber composites.” Journal of Reinforced Polymers and composites, Vol. 25, pp. 771-782.

[6]   Bijwe, J., Tewari, U.S., and Vasudevan, P., 1989 “Friction and wear studies of short glass fiber reinforced polythermide composite.” Wear, Vol. 132, pp. 247-264.

[7]   Viswanth, B., Verma, A.P., and Rao, C.V.S.K., 1991, “Effect of fiber geometry on friction and wear of glass fiber-reinforced composites.” Wear, Vol. 145, pp. 315-327.

[8]   Tripaty, B.S., Furey, M.J., 1993, “Tribological behaviour unidirectional graphiteepoxy and carbon -PEEK composites. Wear, Vol. 162-164, pp. 385-396.

[9]   EI-Sayed, A.A, EI-Sherbiny, M.J., Abo-EI-Ezz, A.S., Aggag, G.A., 1995, “Friction and wear properties of polymeric composite materials for bearing applications.” Wear, Vol. 184, pp. 45-53.

[10]   Cirino, M., Friedrich, K., and Pipes, R.B., 1988, “The effect of fiber orientation on the abrasive wear behaviour of polymer composite materials.” Wear, Vol. 121, pp.127-141.

[11]   Lancaster, J. K., 1972, “Lubrication of carbon fiber-reinforced polymers : Part II— Organic fluids.” Wear, Vol. 20, No. 3, pp. 335-351.

[12]   Briscoe, B. J., Pogosion, A. K., and Tabor, D., 1974, “The friction and wear of high Density polyethylene; the action of lead oxide and copper oxide fillers.” Wear, Vol.27, pp. 19-34.

[13]   Tanaka, K., 1986, Effect of various fillers on the friction and wear of PTFE-based composites, In: Friction and Wear of Polymer composites, Volume 205, pp. 137-174, (Friedrich K editor), Elsevier, Amsterdam.

[14]   Bahadur, S., Fu, Q., and Gong, D., 1994, “The effect of reinforcement and the synergism between CuS and carbon fiber on the wear of nylon.” Wear, Vol. 178, pp.123-130.

[15]   Bahadur, S., and Tabor, D., 1985, Role of fillers in friction and wear behaviour of HDPE In: Polymer wear and its control, Volume 287-268 (L.H. Lee (ed.) ACM symposium series, Washington DC.

[16]   Bahadur, S., Gong, D., Anderegg, J. W., 1992 “The role of copper composites as fillers in the transfer film formation and wear of Nylon.” Wear, Vol. 154, pp. 207-223.

[17]   Kishore, Sampathkumaran, P., Seetharamu, S., Vynatheya, S., Murali, A., Kumar, R. K., 2000, “SEM observations of the effect of velocity and load on the slide wear characteristics glass-fabric-epoxy composites with different fillers.” Wear, Vol. 237, pp. 20-27.

[18]   Kishore, Sampathkumaran, P., Seetharamu. S., Thomas, P., Janardhana, M. A., 2005, “Study on the effect of the type and content of filler in epoxy-glass composite system on the friction and wear characteristics.” Wear Vol. 259, pp. 634-641.

[19]   Wang, J., Gu, M., Songhao, Ge, S., 2003, “The role of the influence of MoS2 on the tribological properties of carbon fiber reinforced Nylon 1010 composites.” Wear, Vol. 255, pp. 774-779.

[20]   Basavarajappa, S., Chandramohan, G. C., 2005, “Wear studies on metal matrix composites: A Taguchi Approach.” J. of Materials Sci. and Tech., Vol. 21, No. 6, pp. 348-350.

[21]   Viswanath, B., Verma, A. P., and Kameswara Rao, C. V. S., 1992, “Effect of matrix content on strength and wear of woven roving glass polymeric composites.” Comp Sci Tech., Vol. 44 pp. 77-86.

[22]   Mody, P. B., Chou, T. W., Friedrich, K., 1988, “Effect of testing conditions and microstructure on the sliding wear of graphite fiber/PEEK matrix composites.” J. Mater. Sci., Vol. 23, pp. 4319-4330.

[23]   Annual hand book of ASTM standards, Section 3,03,02, ASTM G-99 (1995), Phildelphia, USA.

 
 
Top