ENG  Vol.2 No.4 , April 2010
A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius
ABSTRACT
The present study considers a finite element analysis of elastic-plastic axi-symmetric hemispherical contact for a frictionless deformable sphere pressed by a rigid flat. The material of the sphere is modeled as elastic perfectly plastic. Analysis is carried out to study the effect of varying modulus of elasticity and sphere radius in wide range of dimensionless interference until the inception of plasticity as well as in plastic range. Results are compared with previous elastic-plastic models. It is found that materials with Young’s modulus to yield strength (E/Y) ratio less than and greater than 300 show strikingly different contact phenomena. The dependency of E on dimensionless interference at which the plastic region fully covers the surface is observed. However with different radius, finite element study exhibits similar elastic-plastic phenomena.

Cite this paper
nullP. Sahoo and B. Chatterjee, "A Finite Element Study of Elastic-Plastic Hemispherical Contact Behavior against a Rigid Flat under Varying Modulus of Elasticity and Sphere Radius," Engineering, Vol. 2 No. 4, 2010, pp. 205-211. doi: 10.4236/eng.2010.24030.
References
[1]   J. A. Greenwood and J. B. P. Williamson, “Contact of Nominally Flat Surfaces,” Proceedings of the Royal Society of London, Vol. A295, 1966, pp. 300-319.

[2]   S. Timoshenko and J. N. Goodier, “Theory of Elasticity,” McGraw-Hill, New York, 1951.

[3]   E. J. Abbott and F. A. Firestone, “Specifying Surface Quality-A Method Based on Accurate Measurement and Comparison,” Journal of Mechanical Engineering, No. 55, 1933, pp. 569-572.

[4]   W. R. Chang, I. Etsion and D. B. Bogy, “An Elastic-plastic Model for the Contact of Rough Surfaces,” Journal of Tribology, Vol. 109, No. 2, 1987, pp. 257-263.

[5]   Y. Zhao, D. M. Maietta and L. Chang, “An Asperity Micro Contact Model Incorporating the Transition from Elastic Deformation to Fully Plastic Flow”, Journal of Tribology, Vol. 122, No. 1, 2000, pp. 86-93.

[6]   L. Kogut and I. Etsion, “Elastic-plastic Contact Analysis of a Sphere and a Rigid Flat,” Journal of Applied Mechanics, Vol. 69, No. 5, 2002, pp. 657-662.

[7]   D. Tabor, “The Hardness of Metals,” Clarendon Press, Oxford, 1951.

[8]   L. Kogut and I. Etsion, “A Semi-analytical Solution for the Sliding Inception of a Spherical Contact,” Journal of Tribology, Vol. 125, No. 3, 2003, pp. 499-506.

[9]   V. Brizmer, Y. Kligerman and I. Etsion, “The Effect of Contact Conditions and Material Properties on the Elasticity Terminus of a Spherical Contact,” International Journal of Solids and Structures, Vol. 43, 2005, pp. 5736-5749.

[10]   R. L. Jackson and I. Green, “A Finite Element Study of Elasto-plastic Hemispherical Contact against a Rigid Flat,” Journal of Tribology, Vol. 127, No. 2, 2005, pp. 343-354.

[11]   J. J. Quicksall, R. L. Jackson and I. Green, “Elasto- plastic Hemispherical Contact Models for Various Mechanical Properties,” Journal of Engineering Tribology, Vol. 218, No. 4, 2004, pp. 313-322.

[12]   R. L. Jackson, I. Chusoipin and I. Green, “A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts,” Journal of Tribology, Vol. 127, No. 3, 2005, pp. 484-493.

[13]   S. Shankar and M. M. Mayuram, “A Finite Element Based Study on the Elastic-plastic Transition Behavior in a Hemisphere in Contact with a Rigid Flat,” Journal of Tribology, Vol. 130, 2008, pp. 1-6.

[14]   R. Malayalamurthi and R. Marappan, “Elastic-plastic Contact Behavior of a Sphere Loaded against a Rigid Flat,” Mechanics of Advanced Materials and Structures, Vol. 15, No. 5, 2008, pp. 364-370.

 
 
Top